Bosch Professional GTS 10 J Manual Original página 37

Table saw
Saw blade diameter
Base blade thickness
Min. tooth thickness/offset
Hole diameter
Maximum workpiece dimensions: (see "Maximum workpiece dimensions", page 41)
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Noise information
Noise emission values determined according to EN
62841-3-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 111 dB(A); sound power level 124
dB(A). Uncertainty K = 3 dB.
Wear hearing protection
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Fitting
Avoid starting the power tool unintentionally. The
u
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Table saw with fitted saw blade (26) and riving knife (7)
– Angle guide (3)
– Profile rail (28)
– "Profile rail" fastening set (44) (guide plate, knurled nut,
screw, washer)
– Parallel guide (9)
– Additional parallel guide (41)
– "Additional parallel guide" fastening set (42) (3 fastening
screws, 3 washers, 3 wing nuts)
– Protective cover (6)
– Hex key (21)
– Hex key (20)
Bosch Power Tools
GTS 10 J
mm 254
mm <2.2
mm >2.4
mm 25.4
– Ring spanner (22)
– Push stick (23)
– Table insert(25)
– Dust extraction adapter (32)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Fitting individual components
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
– Make sure that you remove the packaging material be-
neath the motor block.
The following parts of the tool are attached directly to the
housing: Push stick (23), ring spanner (22), hex key (21)
and (20), parallel guide (9), angle guide (3), dust extraction
adapter (32), additional parallel guide (41) with fastening
set (42), protective cover (6).
– If you require one of these parts, remove it carefully from
its storage location.
Positioning the riving knife (see figures a1–a2)
Note: If necessary, clean all parts to be fitted before you po-
sition them.
– Turn the crank (18) clockwise as far as possible so that
the saw blade (26) is in the highest possible position
above the saw table.
– Loosen the clamping lever (34).
– Slide the riving knife (7) towards the clamping lever (34)
until it can be pulled upwards.
– Pull the riving knife all the way up until it is positioned ex-
actly over the centre of the saw blade.
– Allow both pins (35) to engage in the lower bore holes in
the riving knife and then retighten the clamping lever
(34).
English | 37
GTS 10 J
254
<2.2
>2.4
25.4
1 609 92A 5C2 | (26.07.2019)