Descargar Imprimir esta página

Bosch Professional GTS 10 J Manual Original página 38

Ocultar thumbs Ver también para Professional GTS 10 J:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 60
38 | English
Fitting the table insert (see figure b)
– Hook the table insert (25) into the rear recesses (36) of
the tool chamber.
– Guide the table insert down.
– Press down on the table insert until it engages in the front
of the tool chamber.
The front side of the table insert (25) must lie flush with or a
little below the saw table; the rear must lie flush with or a
little above the saw table (see "Adjusting the level of the
table insert (see figure N)", page 43).
Fitting the protective cover (see figures c1–c2)
Note: Only fit the protective cover when the riving knife is in
the top position directly over the centre of the saw blade
(see figure a2). Do not fit the protective cover when the riv-
ing knife is in the bottom position (position when delivered/
position for sawing grooves) (see figure a1).
– Loosen the clamping lever (37) and remove the protect-
ive cover (6) from the bracket (33).
– Hold the saw blade guard (upper metal rail) of the pro-
tective cover (6) with one hand, while using the other
hand to move the clamping lever (37) up.
– Push the guide pin (38) backwards into the groove on the
riving knife (7).
– Move the protective cover (6) down until the saw blade
guard (upper metal rail) is parallel with the surface of the
saw table (8).
– Push the clamping lever (37) down. The clamping lever
must be felt and heard to engage; the protective cover (6)
must be securely and safely fitted.
Always check that the blade guard can move properly
u
before use. Do not use the power tool if the blade
guard cannot move freely and does not close immedi-
ately.
Fitting the parallel guide (see figure d)
The parallel guide (9) can be positioned on either the left or
the right of the saw blade.
– Loosen the clamping handle (39) of the parallel guide
(9). This lightens the load on the V guide (40).
– First insert the parallel guide with the V guide into the
guide groove (10) of the saw table. Then position the par-
allel guide in the front guide groove (1) of the saw table.
The parallel guide can now be moved freely.
– To secure the parallel guide, push the clamping handle
(39) down.
Fitting the additional parallel guide (see figure e)
To saw narrow workpieces and bevel angles, you must fit
the additional parallel guide (41) on the parallel guide (9).
The additional parallel guide can be fitted on the left or right
of the parallel guide (9) as required.
Use the "additional parallel guide" fastening set (42) (two
fastening screws, two washers, two wing nuts) for fitting the
guide.
– Slide the fastening screws through the lateral holes on the
parallel guide (9).
1 609 92A 5C2 | (26.07.2019)
– The heads of the screws are used to guide the additional
parallel guide.
– Slide the additional parallel guide (41) over the heads of
the fastening screws.
– Place the washers on the fastening screws and tighten the
screws using the wing nuts.
Fitting the angle guide (see figures f1−f2)
– Push the rail (43) of the angle guide (3) into one of the
guide grooves (5) provided in the saw table.
To make it easier to position long workpieces, the angle
guide can be extended with the profile rail (28).
– If necessary, fit the profile rail on the angle guide using
the fastening set (44).
Dust/chip extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
The dust/chip extraction system can be blocked by dust,
chips or fragments of the workpiece.
– Switch the power tool off and pull the mains plug out of
the socket.
– Wait until the saw blade has come to a complete stop.
– Determine the cause of the blockage and eliminate it.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
To prevent the risk of fire when sawing aluminium,
u
empty the chip ejector and do not use chip extraction.
Emptying the chip ejector (see figure g)
You can empty the chip ejector (31) to remove workpiece
fragments and large chips.
– Switch the power tool off and pull the mains plug out of
the socket.
– Wait until the saw blade has come to a complete stop.
– Loosen the fastening screw (45) using the hex key (21).
– Pull out the chip ejector (31) and remove the workpiece
fragments and chips.
– Refit the chip ejector on the power tool.
External dust extraction (see figure h)
Use the dust extraction adapter (32) provided to connect a
dust extractor to the chip ejector (31).
Bosch Power Tools

Publicidad

loading

Este manual también es adecuado para:

3 601 m30 5023 601 m30 5723 601 m30 5323 601 m30 562Gts 10 j professionalGts 10 professional