Metabo BS 18 L BL Instrucciones De Manejo página 8

en ENGLISH
3. If the current is too high (for example, if the
machine seizes continuously for long periods),
the machine switches off.
Switch off the machine at the trigger switch (7).
Then continue working as normal. Try to prevent
the machine from seizing.
5.2 Battery pack
Charge the battery pack before use.
Recharge the battery pack if performance
diminishes.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
In case of Li-Ion battery packs with capacity and
signal display (12) (equipment-specific):
- Press the button (13), the LEDs indicate the
charge level.
- The battery pack is almost flat and must be
recharged if one LED is flashing.
Removing and inserting the battery pack
Removal: press the battery pack release button (10)
and pull the battery pack (11) forwards.
Insertion: Slide the battery pack (11) in until it
engages.
5.3 Setting the direction of rotation,
engaging the transporting safety device
(switch-on lock)
Do not activate rotation selector switch (6)
unless the motor has completely stopped!
Actuate the rotation selector switch (direction of
rotation setting, transporting safety device) (6).
See page 2:
R = Clockwise setting
L = Anti-clockwise setting
0 = middle position: transportation safety device
(Switch-on lock) set
5.4 Selecting gear stage
1. gear (low speed,
1 2
particularly high torque, preferable for
screwing)
2. gear (high speed, preferable for drilling)
2
5.5 Set torque limitation, screw driving,
drilling, impact drill
Machines with the designation BS...:
1...20 = Set torque (with torque limitation) by
turning the sleeve (2) - intermediate
settings are also possible.
= Set drilling by turning the sleeve (2) (max.
torque, without torque limitation)
To avoid overloading the motor, do not
jam the spindle.
Machines with the designation SB...:
= Set screwdriving by turning the sleeve
(3)
AND
8
set the torque (with torque limitation) by
turning the sleeve (4) - intermediate
settings are also possible.
= Set drilling by turning the sleeve (3) (max.
torque, without torque limitation)
To avoid overloading the motor, do not
jam the spindle.
= Set impact drilling by turning the sleeve
(3) (max. torque, without torque limitation)
To avoid overloading the motor, do not
jam the spindle.
5.6 Change accessory
Opening the drill chuck:
Turn the drill chuck sleeve (1) in clockwise direction.
Clamping the tool:
Open the drill chuck and insert the tool as far as
possible. Turn the drill chuck sleeve (1) in anti-
clockwise direction until the tool is clamped
securely. With a soft tool shank, retightening may
be required after a short drilling period.
5.7 On/Off switch, modifying the speed
Switching on, speed: press the trigger switch (7).
Press in the trigger switch to increase the rotational
speed.
Switching off: release the trigger switch (7).
5.8 Drill chuck with "Quick" change system
(for BS 18 L BL Q, Powermaxx BS 12 BL
Q)
Removal: See page 2, fig. A. Push the interlocking
ring forward (a) and pull off the drill chuck (b).
Mounting: Push the interlock ring forward and
move the chuck as far as the limit stop on the drill
spindle.
5.9 Drill chuck (for BS 18 L BL, SB 18 L BL,
Powermaxx BS 12 BL, Powermaxx SB 12
BL)
See page 2, fig. B.
Remove locking screw. Caution left-handed thread!
Clamp an Allen key in the chuck and strike lightly
with a rubber hammer to loosen, then unscrew.
Employ the same procedure when attaching the
chuck, except in reverse order.
6. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
See page 4.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
A Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.
B Angle screwdriver attachment.
C Battery charger
D Bit holder with Quick replacement system
E Bit box