EINHELL TC-HP 2042 PC Manual De Instrucciones Original página 19

Cleaning agent container
You can adjust the quantity of cleaning agent you
want to add by turning (+ / -) on the setting wheel
(11). We recommend using the cleaning agent
sparingly.
5.2.3 Fitting the handle (Fig. 5)
Push the handle (1) onto the pressure washer (5)
and secure it using the 4 screws (long thread).
5.2.4 Assembling the terrace cleaner (Figs.
6-9)
Insert the extension for the terrace cleaner (16)
into the recess provided.
Then turn the terrace cleaner (16) over and insert
the two screws (short thread). Then place the
rotor (17) on the terrace cleaner (16) and secure
this by inserting the clip.
You can then attach the terrace cleaner (16) to
the extension (8) using the quick-lock system
(12).
5.2.5 Connecting the high-pressure hose
(Fig. 3/4)
Connect the high-pressure hose (15) to the gun
(8) and the high-pressure cleaner (5).
Note:
The connections for the high-pressure hose
and the accessories are equipped with a quick
connection system (12). To connect, simply push
the hose or the accessory onto the respective
connection. To remove, simply actuate the quick
connection system (12) and you can remove the
hose or the accessory.
Each time before fi tting, always check that the
quick connection system (12) is correctly enga-
ged. Do this by pulling briefl y on the hose or the
accessory.
5.2.6 Water inlet connector (Fig. 1/4)
The connection for the water inlet (4) is equipped
with a connector for standard hose coupling sys-
tems. Plug the hose coupling on the supply hose
(min. Ø 1/2") to the water inlet connector (4).
Always use a reinforced hose with a standard
coupling for the water inlet. The hose should be at
least 6 m in length. (Not supplied)
A backfl ow preventer must be installed between
the drinking water and the pressure cleaner! Ask
your local plumber about this.
Anl_SA_TC_HP_2042_PC_SPK8.indb 19 Anl_SA_TC_HP_2042_PC_SPK8.indb 19
GB
5.2.7 Electrical connections (Fig. 1)
•
Before you connect the equipment to the
power supply make sure that the data on the
rating plate are identical to the supply voltage.
•
If you use any extension cables, make sure
that they are suitable for outdoor use and
have large enough wires:
1 – 10 m: 1.5 mm²
10-30m: 2.5 mm²
•
Insert the power plug on the power cable (6)
into the socket outlet.
6. Operation
The equipment consists of an assembly with a
pump, which is encased in a shock absorbing
housing. For an optimal working position the
equipment comes with a lance and a non-slip
gun, whose shape and confi guration comply with
the applicable regulations.
6.1 Using for the fi rst time
Once you have completely assembled the pres-
sure cleaner and made all the connections, pro-
ceed as follows:
Open the water inlet. Press safety pin „a" (Fig. 2)
on the spray gun and pull back trigger lever „b"
(Fig. 2) in order to bleed the trapped air out of the
equipment.
Turn on the equipment by switching the On/Off
switch (Fig. 1/3) to "ON".
Now activate the trigger lever (b).
To turn off , release the trigger lever (b). The
equipment will then go into standby. As soon as
you press the trigger lever (b) again, the pressure
cleaner will restart.
To turn off the pressure cleaner completely, set
the On/Off switch (Fig. 1/3) to "OFF".
6.2 Using cleaning agent
•
Fill the cleaning agent container (10) with sui-
table cleaning agent.
•
The cleaning agent will be added automati-
cally in low-pressure mode.
Note:
Use only cleaning agents which are expressly
suitable for high-pressure cleaners.
- 19 -
25.04.16 13:23 25.04.16 13:23