Descargar Imprimir esta página

EINHELL TH-RH 800 E Manual De Instrucciones página 17

Ocultar thumbs Ver también para TH-RH 800 E:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 81
5.2 Fitting and adjusting the depth stop
(Fig. 3/Item 7)
The depth stop (7) is held in place by the additi-
onal handle (6) by clamping. The clamp can be
released and tightened by turning the handle.
Release the clamp and fit the depth stop (7)
in the recess provided for it in the additional
handle.
Set the depth stop (7) to the same level as
the drill bit.
Pull the depth stop back by the required dril-
ling depth.
Turn the handle on the additional handle (6)
until it is secure.
Now drill the hole until the depth stop (7) tou-
ches the workpiece.
5.3. Tool insertion (Fig. 4)
Clean the tool before insertion and apply a
thin coating of drill bit grease to the shaft of
the tool.
Pull back and hold the locking sleeve (2).
Insert the dust-free tool into the tool mounting
as far as it will go whilst turning it. The tool will
lock itself.
Check that it is properly secure by pulling the
tool.
5.4 Tool removal (Fig. 5)
Pull back and hold the locking sleeve (2) and re-
move the tool.
6. Operation
Danger
To prevent all danger, the machine must only be
held using the two handles (6/8). Otherwise there
may be a risk of suff ering an electric shock if you
drill into cables.
6.1 ON/OFF switch (Fig. 6/Item 4)
First fit a suitable drill bit into the tool (see
5.3).
Connect the mains plug to a suitable socket.
Position the drill in the position you wish to
drill.
To switch on:
Press the ON/OFF switch (4)
Continuous operation:
Secure the ON/OFF switch (4) with the locking
button (5).
Anl_TC_RH_800_E_SPK9.indb 17
Anl_TC_RH_800_E_SPK9.indb 17
GB
To switch off :
Press the ON/OFF switch (4) briefl y.
6.2 Adjusting the speed (Fig. 6/Item 4)
You can infinitely vary the speed whilst using
the tool.
Select the speed by applying a greater or les-
ser pressure to the ON/OFF switch (4).
Select the correct speed: The most suitable
speed depends on the workpiece, the type of
use and the drill bit used.
Low pressure on the ON/OFF switch (4): Lo-
wer speed
Greater pressure on the ON/OFF switch (4):
Higher speed
Tip: Start drilling holes at low speed. Then
increase the speed in stages.
Benefi ts:
The drill bit is easier to control when starting
the hole and will not slide away.
You avoid drilling messy holes (for example in
tiles).
6.3 Preselecting the speed (Fig. 6/Item 9)
The speed setting ring (9) enables you to
define the maximum speed. The ON/OFF
switch (4) can only be pressed to the defined
maximum speed setting.
Set the speed using the setting ring (9) on the
ON/OFF switch (4).
Do not attempt to make this setting whilst the
drill is in use.
6.4 Clockwise/Counter-clockwise switch
(Fig. 6/Item 10)
Change switch position only when the drill is
at a standstill!
Switch the direction of the hammer drill using
the clockwise/counter-clockwise switch (10):
Direction
Clockwise
(forwards and drill)
Counter-clockwise
(reverse)
- 17 -
Switch position
Pushed in to the right
Pushed in to the left
15.02.2019 06:29:42
15.02.2019 06:29:42

Publicidad

loading

Este manual también es adecuado para:

42.579.20