Additional Information; Troubleshooting - PIONEER DJ XDJ-700 Manual De Instrucciones

Additional information

Troubleshooting

! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points
below and the [FAQ] for the [XDJ-700] on the Pioneer DJ support site.
http://pioneerdj.com/support/
Sometimes the problem may lie in another component. Inspect the other components and electrical appliances being used. If the problem cannot
be rectified, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
! This unit may not operate properly due to static electricity or other external influences. In this case, proper operation may be restored by turning the
power off, waiting 1 minute, then turning the power back on.
Problem
File cannot be played.
No sound is produced, or sound is
distorted or noisy.
File information is not properly
displayed.
Track search operation takes too long.
Back cue function does not work.
Loop play function does not work.
Settings are not stored in the memory. Has the power been turned off directly after
USB device is not recognized.
Cue points or loops are not stored on
a USB device.
Cue or loop points of tracks recorded
on USB devices are not displayed.
Playback does not start immediately
after pressing the button to reloop or
play in reverse.
The playing address display is not
displayed in the remaining time mode.
Time is required to read USB devices
(flash memory drives and hard discs).
Library browsing is not possible.
[HISTORY] is not displayed.
Nothing is displayed.
8
En
Check
Is the file copyright-protected (by DRM)?
Are you operating the connected DJ mixer
properly?
Is this unit placed near a TV?
Is [LANGUAGE] properly set?
Is the information recorded in a language not sup-
ported by this unit?
Is the auto cue function activated?
—
Is a cue point set?
Are loop points set?
changing the setting?
Is the USB device properly connected?
Is the USB device connected via a USB hub?
Is the USB device supported by this unit?
Is the file format supported by this unit?
—
Are you trying to store more points than the limit?
Is the USB device write-protected?
Is there sufficient free space on the USB device?
Was the USB device properly stopped before it
was disconnected the last time?
Is the quantize function on?
—
Is there a large number of folders or files recorded
on the USB device?
Are files other than music files stored on the USB
device?
Is a medium on which library information is
recorded loaded?
Is a USB device loaded?
Is the auto standby function activated?
Remedy
Copyright-protected files cannot be played.
Check the operation of the DJ mixer.
Turn the TV's power off or install this unit and TV away from each other.
Set [LANGUAGE] to the proper language.
When creating files using DJ software, etc., record the information in a language
supported by this unit.
Track searching may take some time when there are long silent sections
between tracks.
If track searching is not possible within 10 seconds, a cue point is set at the
beginning of the track.
Set a cue point.
Set loop points.
After changing settings, wait at least 10 seconds before turning the power off.
Connect the device securely (all the way in).
USB hubs cannot be used.
This player only supports USB mass storage class devices.
This player supports portable flash memory and digital audio playback devices.
Check the file format of the connected USB device. For the file formats sup-
ported by this unit, see Usable media on page 4 .
Turn the power off then back on.
Ten cue points or loop points per track can be stored on a USB device.
If you try to store more points than the limit, [CUE/LOOPPOINT FULL] is dis-
played and the points cannot be stored. In this case, delete some points before
storing new ones.
If the USB device is write-protected, [USB FULL] is displayed and the points
cannot be stored. Disable the write-protection then store the cue or loop points
again.
If there is not enough free space on the USB device, [USB FULL] is displayed
and the points cannot be stored. Free up some space then store the cue or loop
points again.
Points may not be displayed if the SD memory card/USB device is removed
without performing the proper stopping procedure or if this unit's power is
turned off.
Make sure the USB indicator has stopped blinking before removing the USB
device or turning off the power of the unit.
When the quantize function is on, playback starts from the nearest beat position
at the time the button is pressed. If you want the operation to be performed the
instant the button is pressed, turn the quantize function off.
When playing files recorded in VBR, it may happen that the set cannot detect the
length of the track immediately and that some time is required for the playing
address display to appear.
When there are many folders or files, some time may be required for loading.
When files other than music files are stored in folders, time is required to read
them as well. Do not store files or folders other than music files on the USB
device.
The library browse mode is only set when media on which library information
is recorded are loaded. When a medium on which no library information is
recorded is loaded, the folder browse mode is set.
The [HISTORY] function can only be used for DJ players on which a USB device
is loaded.
This unit is shipped with the auto standby function set to on. If you do not want
to use the auto standby function, set [AUTO STANDBY] on the [UTILITY] menu
to [OFF].