Publicidad
Idiomas disponibles
Idiomas disponibles
• See table below for the number to speed relationship on the
dial and usage information
Number
RPM
1
11,500
2
16,500
3
21,000
4
25,000
5
29,000
6
31,000
IMPORTANT: Operating at reduced speed increases the risk of
damage to the Router (1) as a result of overload. Use very slow feed
rates and/or multiple shallow cuts.
Hand-held operation
WARNING: To minimise the risk of kickback, the direction of
routing must always be in opposition to the cutter's rotational
direction.
Notes:
• Ensure all PPE/safety equipment is used when operating this
tool
• Ensure the workpiece is securely clamped to prevent any
movement during operation
• Hold the Router (1) firmly using both hands to control the
Router and keep an even pressure and movement when cutting
• The cutter rotates in a clockwise direction (A on Fig. XIII)
• When edge routing or trimming on the outside edge, ensure
the workpiece is to the left of the cutter (B and C on Fig. XIII) and
work in an anticlockwise direction
(Figs XIV, XV, XVI, XVIII, XIX, XX)
• When routing internal edges, ensure the edge to be cut is to the
left of the cutter and work around the internal shape
(D on Fig. XIII) in a clockwise direction
• If cutting all the way through the material, fix a sacrificial board
to the underside of the workpiece
• When edge cutting natural timbers, always pass along the end
grain first, then by the long grain. If splintering or breakout
occurs, this will be remedied when passing down the long grain
• Do not operate the Router upside down unless securely
mounted in a well-guarded router table
• If a deep cut is required for a plunge cut, do not make the
full depth for the first pass. Instead, make more passes with a
shallower depth of cut and adjust the cutting depth gradually
in smaller increments. The Depth Stop (30) and Depth Turret
(31) can be used for changing depths to pre-set 5mm (
increments
Routing with the roller guide
• Use the Timmer Base (8) and Roller Guide (7) for routing edges
with router bits without a guide bearing or pilot
• Ensure the Router (1) is installed in the Trimmer Base with
the Roller Guide (see 'Fitting to trimmer base' and 'Fitting &
adjusting the roller guide')
817698_OwnerManual.indd 19
817698_OwnerManual.indd 19
• Ensure the depth of cut is set as required (see 'Setting the depth
of cut with the trimmer base')
1. Power the Router ON then guide the Router from the side
Usage
toward the workpiece until the Guide Bearing (40) contacts the
edge of the workpiece (Figs XVI XVII)
Bits and cutters
2. Guide the Router along the workpiece's edge, ensuring the base
with a larger
rests on the workpiece at the correct angle
diameter
IMPORTANT: When using the Trimmer Base (8) with the Roller
Guide (7), adjust the Guide Bearing (40) (Fig. XVII) with enough
vertical clearance from the cutter and consider cutter's diameter
when setting the horizontal axis so the Guide Bearing can guide
Bits and cutters
the cutter along the edge of the workpiece.
with a smaller
diameter.
Shaping or moulding
Laminates, plastics
• If shaping or moulding without a parallel guide (Guide Fence
and softwoods
(6) or batten), a router bit with a guide bearing or pilot must be
used (Figs XIV XV)
• Ensure the depth of cut is set as required (see 'Before Use'
sections pertaining to setting the depth of cut)
1. Power the Router (1) ON then guide the Router from the side
toward the workpiece until the guide bearing on the Router Bit
(not supplied) (48) contacts the edge of the workpiece
2. Guide the Router along the workpiece's edge, ensuring the base
rests on the workpiece at the correct angle
IMPORTANT: Excessive pressure could damage the workpiece.
Note: To prevent edge burn, clamp a sacrificial piece of material
of the same thickness as the workpiece before and after the
workpiece. Start the cutting on the first sacrificial piece, guide
along onto the workpiece then beyond to finish on the other
sacrificial piece. Doing this will prevent beginning burn and end
burn on the workpiece.
Routing with a parallel guide or guide fence
• Use the Guide Fence (6) assembled in configuration A or B
(Fig. VI), fastened to the Plunge Base (9) (see 'Fitting & adjusting
the guide fence'), for edge-parallel cuts or batten-parallel cuts
(Figs XIX and XX)
• Ensure the depth of cut is set as required (see 'Before Use'
sections pertaining to setting the depth of cut)
1. Adjust to required distance from the Guide Fence to the cutter
2. Power the Router (1) ON then guide the Router with a controlled
feed and lateral pressure along the workpiece's edge
Routing with a batten guide
See Fig. XVIII
• A batten guide can be used when clamped on top of the
workpiece (see Fig. XXIV for distances to the edge of the bases
from the centre of the cutter as an approximate guide)
• The Guide Fence (6) in configuration B (Fig. VI) can be used with
the batten (Fig. XX)
• It is recommended that a test cut be performed on scrap
⁄
3
")
material prior to using the workpiece
6 4
Freehand routing
See Fig. XXI
• The Router (1) can be used for creative freehand or signwriting
work without the use of a guide
• Practise on scrap material before working on the workpiece
• Draw the design on the workpiece then router the design using
shallow passes
EN
19
11/11/2022 10:25
11/11/2022 10:25
Publicidad
