Descargar Imprimir esta página

EINHELL TC-SY 600 Manual De Instrucciones página 21

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 78
material will be deposited on surfaces there.
Unscrew the container (12) from the paint
spray gun.
Align the material tube (11) for the object you
are working on.
Spaying on horizontal objects: Rotate the ma-
terial tube (11) towards the front.
Spaying on raised objects: Rotate the materi-
al tube (11) towards the rear.
Never continue spraying until the container
is completely empty. If the material tube no
longer reaches the spray material, the spray
flow will be interrupted and the coverage on
the surface will be uneven.
Once you have performed the viscosity mea-
surement as described in 6.1.1, place the
container (12) on some paper, pour in the ma-
terial you have prepared and tightly screw the
container (12) back into the paint spray gun.
The paint spray gun may only be set down
on a clean, even surface. Otherwise it may
tip over.
After each cleaning (see 8.1) or change of fan
pattern (see 6.3), tighten the air cap retaining
ring (1) to prevent material from leaking out
between the air cap retaining ring and the air
cap (2).
6.4 Adjusting the fan pattern (Fig. 7)
You can set the paint spray gun to produce three
diff erent fan patterns to suit your needs.
Loosen the air cap retaining ring (1) and rotate
the air cap (2) to the desired position. Re-tighten
the air cap retaining ring.
Selecting the fan pattern:
A: vertical fan
-> for horizontal surfaces
B: horizontal fan
-> for vertical surfaces
C: Round fan
-> for corners, edges and surfaces that are dif-
fi cult to access
Risk of injury!
Never press the trigger while you are adjusting
the jet.
6.5 Adjusting the material fl ow (Fig. 8)
You can rotate the max. paint volume control to
regulate the material fl ow.
Anl_TC_SY_600_700_SPK13.indb 21
Anl_TC_SY_600_700_SPK13.indb 21
GB
- direction-> lower material fl ow
+ direction-> higher material fl ow
6.6 Spraying techniques
The results you get depend on how smooth
and clean the surface is. The surface must be
carefully prepared and free of dust.
Surfaces, threads, etc. which should not be
sprayed must be covered.
Always set the spray gun down on cardboard
or something similar. You can use the card-
board as a target to properly adjust the spray
gun.
Important:
Always begin spraying outside of the area to be
sprayed and avoid interrupting spraying inside the
area to be sprayed.
Wrong (Fig. 9): If you only rotate the spray
gun from side to side, the gun will produce a
heavy mist and the coverage will be uneven.
Right (Fig. 10): Always hold the spray gun at
the same distance (about 5-15 cm) from the
surface you are working on.
Move the spray gun uniformly laterally or up
and down depending on the fan pattern.
Uniform motion of the spray gun produces
uniform finish quality.
If material residue is deposited on the nozzle
(3) and the air cap (2), clean both parts with
solvent or water.
6.7 Transport
Carry the spray gun by the handle (9) or the
shoulder strap (17).
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
- 21 -
21.06.2023 10:56:22
21.06.2023 10:56:22

Publicidad

loading

Este manual también es adecuado para:

Stc-sy 700 s42.600.1542.600.20