Peg-Perego book cross Instrucciones De Uso página 13

AVOID TRAPPING OR INJURY
WARNING
_
DO NOT ADD ANY MATTRESS
ARE NOT APPROVED BY THE
MANUFACTURER.
WARNING
_
NOT MAKE ANY ALTERATIONS
OR MODIFICATIONS TO THE
STROLLER WITH PRODUCTS
NOT SUPPLIED BY THE
MANUFACTURER AS THIS
MAY CAUSE INSTABILITY OR
STRUCTURAL DEMAGE NOT
COVERED UNDER WARRANTY.
NOTICE
THIS ARTICLE MEETS OR
EXCEEDS ALL REQUIREMENTS
COVERED IN ASTM F833
STANDARD AND LATEST
REVISIONS.
COMPONENTS OF THE ITEM
Check the contents of the packaging and if
you have any complaints please contact the
Assistance Service.
_ Book Cross: basket; 2 rear wheels, 1 front
wheel, handlebar with dynamic brake wire,
front bar, hood and rain cover.
INSTRUCTIONS
1 OPENING: Before opening the frame, remove
(without using blades) any die-cut cardboard.
WARNING:
_ DO NOT PULL OR FORCE THE FASTENER
BEYOND ITS LIMIT.
_ DO NOT USE THE FASTENER AS A CARRY
HANDLE OR TO CARRY WEIGHTS.
DO NOT HANG BAGS OR OTHER ACCESSORIES
TO THIS FEATURE.
Press down the side fastener, hold the upper
section of the handle and rotate it towards
you until the frame is fully opened (fig_a).
Open frame (fig_b).
The frame is properly opened when the
attachment on the base clicks into place, as
shown.
2 FITTING THE WHEELS: push the rear wheels
on and make sure that they click into place
(fig_a). To mount the front wheels, fit them
into the uprights until they lock into place
(fig_b).
3 ATTACHING THE MAIN HANDLE: if the handle
tube faces upwards, align it with the stroller
(Fig_a).
Fasten the handle to the frame as shown in
:
the figure (Fig_b).
To complete the operation, press the two
side buttons on the handle (Fig_c) to ensure
the handle pushes in all the way, until it clicks
into place (Fig_d).
: 4 FITTING THE BASKET: if lowered, lift the
basket tube to the horizontal position. Press
DO
the silver buttons under the metal basket
tube located at the back of the stroller (fig_a)
and remove the metal tube (fig_b). Thread
the tube through the fabric loop on the
back of the basket, making sure that the two
silver buttons are facing downward (fig_c).
Re-attach the tube to the housings (fig_d).
5 Secure the two upper basket vinyl eyelets to
the two grey buttons on either side of the
metal tube housing. Please note that the
eyelets open (fig_e).
IMPORTANT! Fasten the three lower basket
loops to the three grey buttons on the rear
bar. Note that the loops open (fig_f).
WARNING! If this operation is not completed
properly, the basket will not support any
weight.
Fasten the front basket flaps to the grey
buttons on the frame (fig_g) and then secure
the basket centrally to the footrest using the
Velcro strap (fig_h).
6 HOOD: Fasten the hood at the back using
the Velcro strip (fig_a), insert the hood
attachments into their slots (fig_b), secure
with the external rubber band to the buttons
on the inside of the handlebar (fig_c), and
finally button the hood laterally to the frame
(fig_d).
7 FIXED OR SWIVEL FRONT WHEELS: to fix
the front wheels, rotate the lever counter
clockwise to the locked padlock (fig_a); to
release the wheels, turn the lever clockwise
to the unlocked padlock (fig_b). On difficult
terrain, we recommend using fixed wheels.
8 BOOK CROSS BRAKE: To engage the brake,
pull the handle on the handlebar towards you
(arrow_a) and block the red lever (fig_b); to
release the brake, release the lever (arrow_c).
Always engage the brake when stationary. To
adjust the brake making it more rigid, loosen
the regulator (fig_d) located on the handlebar
by screwing it outwards. To loosen and soften
the brake, do the opposite.
9 ADJUSTABLE HANDLEBAR: To adjust the
height of the handlebar, press both of the
side buttons at the same time (fig_a) and
swing it into the desired position (fig_b), then
release the buttons.
10 FOOTREST: before adjusting the foot rest,
ensure its cover is accurately fitted; if it isn't,
fit it accordingly. To lower the footrest push
- 13 -