Hunter Road Force Elite GSP9700 Serie Instrucciones Funcionamiento página 8

NEMA L6-20P. This machine must be connected to a 20 amp branch circuit.
Please refer all power source issues to a certified electrician.
A protective ground connection, through the grounding
conductor in the power cord, is essential for safe operation. Use
only a power cord that is in good condition.
For information on converting from single phase NEMA L6-20P
plug to thee phase NEMA L15-20P plug refer to Form 5350-
T, "NEMA L6-20P to NEMA L15-20P Power Plug Conversion
Instructions."
Specific Precautions/Optical Scan Laser
The Optical Scan Laser is a class 1 laser designed to measure the profile of
wheel assemblies. The laser is not a field servicable part. No maintenance is
to be performed on the laser.
Wavelength: 650nm.
Specific Precautions/HammerHead
Indicator (Optional)
The TDC (Top Dead Center) Laser Indicator is a class 2M laser designed
to aid in applying clip-on weights. The laser is not a field serviceable or
adjustable part.
Use caution in regard to reflective materials around the laser and never look
into the laser beam.
LASER RADIATION - DO NOT STARE INTO THE BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
Viewing the laser output with magnifiers or related optical instruments within a
distance of 100mm from the laser aperture may pose an eye hazard.
Image 10.
Turning Power ON/OFF
Push Button Switch
The Road Force Elite GSP9700 is equipped with a push button power switch
®
located on the left side of the LCD support. Use this switch for normal shut
down and restarting procedures.
Main Power Switch
To prevent loss of data, always use the push button switch on
the LCD support to power the balancer on and off. Then use the
main power switch to remove power to the entire unit.
The main power ON/OFF switch is located on the back of the balancer
cabinet. To power the balancer "ON," press the "I" side of the ON/OFF switch.
To turn all power the balancer "OFF," press the "O" side of the ON/OFF switch.
Image 12.
After the Road Force Elite GSP9700 Balancer performs a self-check, the
®
main balance screen will appear indicating the unit is ready for use.
Equipment Installation and Service
Only a Hunter Factory-Authorized Representative should perform installation.
This equipment contains no operator serviceable parts. All maintenance and
repairs must be referred to a qualified Hunter Service Representative.
Equipment Specifications
Electrical
Voltage:
Amperage:
Wattage:
Air
Air Pressure Requirements:
Approximate Air Consumption:
Atmospherics
Temperature:
Relative Humidity:
Altitude:
Sound Pressure Level
Equivalent continuous A-weighted sound pressure at operator's position
does not exceed 70 dB (A).
8
Image 8.
Image 9.
TDC Laser
®
Image 11.
230VAC +10% / -15%, 1 phase,
50/60 Hz, power cable includes
NEMA 20 amp plug, L6-20P
10 amperes
3450 watts (peak)
100-175 PSI (6.9-12.0 bar)
4 CFM (113 Liters/Minute)
+32°F to +122°F (0°C to +50°C)
Up to 95% Non-condensing
Up to 6000 ft. (1829 m)
Explanation of Symbols
These symbols may appear on the equipment.
Alternating current.
Earth ground terminal.
Protective conductor terminal.
l ON (supply) condition.
OFF (supply) condition.
Risk of electrical shock.
Stand-by switch.
Not intended for connection to public
telecommunications network.
Safety Hood Features Safety Hood Features
Hood Autostart
The balancer can be set to automatically spin the wheel upon hood closure.
After a spin, the hood must be raised completely before the balancer will
Autostart again.
For safety, the balancer will not Autostart in "Calibration," "Setup,"
"Diagnostics," if no balancing procedure is selected, or if the Inflation Station
hose is out of its "home position."
Auto Hood Feature
The balancer can be set to automatically raise the hood after a spin has been
completed.
Keep body parts and items away from the hood while a spin is in
progress.
End User License Agreement End User License Agreement
Use of equipment and it's operating software is acknowledgment of
agreement to the terms of the End User Licensing Agreement ("EULA"). The
entire EULA can be found by scanning the QR Code below.
Environmental Information Environmental Information
The following disposal procedure shall be exclusively applied to the machines
having the crossed-out bin symbol on their data plate.
Image 13.
This product may contain substances that can be hazardous to the
environment and to human health if it is not disposed of properly.
The following information is therefore provided to prevent the release of these
substances and to improve the use of natural resources.
Electrical and electronic equipment should never be disposed of in the usual
municipal waste but must be separately collected for their proper treatment.
The crossed-out bin symbol, placed on the product and on this page, reminds
the user that the product must be disposed of properly at the end of its life.
In this way it is possible to prevent that a non specific treatment of the
substances contained in these products, or their improper use, or improper
use of their parts may be hazardous to the environment or to human health.
Furthermore, this helps to recover, recycle and reuse many of the materials
contained in these products.
Electrical and electronic manufacturers and distributors set up proper
collection and treatment systems for these products for this purpose.
At the end of the product's working life, contact your supplier for information
about disposal procedures. When you purchase this product, your supplier will
also inform you that you may return another worn-out appliance to him free of
charge, provided it is of the same type and has provided the same functions
as the product just purchased.
Any disposal of the product performed in a different way from that described
above will be liable to the penalties provided for by the national regulations in
force in the country where the product is disposed of.
English