Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Thank you for buying this product, our company is sure that you will be more
than satisfied with the product's performance. The product is supplied with
a "Warnings" leaflet and an "Instruction booklet". These should both be
read carefully as they provide important information about safety, installa-
tion, operation and maintenance. This product complies with the recognised
technical standards and safety regulations.
1) GENERAL OUTLINE
The LIBRA-UL-R control panel is supplied by the manufacturer with standard
setting. Any alteration must be set by means of the incorporated display
programmer or by means of UNIPRO. The Control unit completely supports
the EELINK protocol.
Its main characteristics are:
- Control of two low-voltage motors up to 40W power
- Electronic torque setting with obstacle detection
- Limit-switch control inputs
- Separate inputs for safety devices
- Incorporated rolling-code radio receiver with transmitter cloning
2) SAFETY
If correctly installed and used, this automation device satisfies the required
safety level standards. However, it is advisable to observe some practical
rules in order to avoid accidental problems.
Before using the automation device, carefully read the operation instructions
and keep them for future reference.
•
Keep children, persons and things outside the automation working area,
particularly during operation.
•
Keep radio control or other control devices out of children's reach, in
order to avoid any unintentional automation activation.
•
Do not intentionally oppose the leaf movement.
•
Do not attempt to open the gate by hand, if the actuator has not been
released by means of the appropriate release knob.
•
Do not modify the automation components.
•
In case of malfunction, disconnect the power supply, activate the emer-
gency release to gain access to the actuator and request the assistance
of a qualified technician (installer).
•
Before proceeding to any external cleaning operation, disconnect the
mains powers supply and at least one of the battery pole, if fitted.
•
Keep the photocell optical components and luminous signal indication
devices clean.Check that the safety devices (photocells) are not obscured
by branches or shrubs.
•
For any direct assistance to the automation system, request the assistance
of a qualified technician (installer).
•
Have qualified personnel check the automation system once a year.
•
Entrance is reserved for vehicles, provide a separate entrance for
pedestrians.
3) FUNCTIONS
FOR THE INSTALLER: Fill in the table with the parameters set, in order to
facilitate future modifications and maintenance operations.
The preset values are indicated between square brackets [ ].
PARAMETER MENU
Automatic Closing Time
Motor 1 torque
Motor 2 torque
Motor 1 slow-down torque
Motor 2 slow-down torque
Opening delay time
Closing delay time
Motor 1 Normal Speed Time
Motor 2 Normal Speed Time
Slow-down speed
Zone
LOGIC MENU
TCA (Automatic Closing Time) [OFF]
3 steps
Impulse lock on opening
Rapid closing
Photocells on opening
Photocell test
No. motors in operation
Lock hold
Start / Close
Fixed code
Radio programming
Master
USER'S MANUAL
[10s]
⎣___⎦
[50%]
⎣___⎦
[50%]
⎣___⎦
[45%]
⎣___⎦
[45%]
⎣___⎦
[1s]
⎣___⎦
[1s]
⎣___⎦
[15s]
⎣___⎦
[15s]
⎣___⎦
[0]
⎣___⎦
[0]
⎣___⎦
⎣___⎦
[OFF]
⎣___⎦
[OFF]
⎣___⎦
[OFF]
⎣___⎦
[OFF]
⎣___⎦
[OFF]
⎣___⎦
[OFF]
⎣___⎦
[OFF]
⎣___⎦
[OFF]
⎣___⎦
[OFF]
⎣___⎦
[ON]
⎣___⎦
[OFF]
⎣___⎦
4) SCRAPPING
Warning: This operation should only be carried out by qualified personnel.
Materials must be disposed of in conformity with the current regulations. In
case of scrapping, the automation devices do not entail any particular risks
or danger. In case of materials to be recycled, these should be sorted out
by type (electrical components, copper, aluminium, plastic etc.).
5) DISMANTLING
Warning: This operation should only be carried out by qualified per-
sonnel.
When the control unit is disassembled to be reassembled on another site,
proceed as follows:
•
Disconnect the power supply and the entire electrical installation.
•
In the case where some of the components cannot be removed or are
damaged, they must be replaced.
WARNINGS
Correct controller operation is only ensured when the data contained
in the present manual are observed. The company is not to be held
responsible for any damage resulting from failure to observe the
installation standards and the instructions contained in the present
manual.
The descriptions and illustrations contained in the present manual are
not binding. The Company reserves the right to make any alterations
deemed appropriate for the technical, manufacturing and commercial
improvement of the product, while leaving the essential product fea-
tures unchanged, at any time and without undertaking to update the
present publication.
ENGLISH
LIBRA-UL-R - Ver. 06 - 3
Publicidad
Tabla de contenido
