Makita MR002G Manual De Instrucciones página 12

Setting the clock time and date
1. Press and hold the Menu/Info button.
2. Rotate the Tuning control knob until "CLOCK ADJ"
appears on the display. Press the Tuning control knob
to enter the setting.
3. The hour setting on the display will begin flashing.
Rotate the Tuning control knob to select the desired
hour, and press the Tuning control knob to confirm
the setting. Then rotate the Tuning control knob to
select the desired minute, and press the Tuning
control knob to confirm the setting.
4. Rotate the Tuning control knob until "DATE ADJ"
appears on the display. Press the Tuning control knob
to enter the setting.
5. Rotate the Tuning control knob to select the desired
year and press the Tuning control knob to confirm the
setting. Then rotate the Tuning control knob to select
the desired month, and press the Tuning control knob
to confirm the setting. Then rotate the Tuning control
knob to select the desired date and press the Tuning
control knob to confirm the setting.
Radio Data System (RDS)
When you set the clock time using the RDS function,
your radio will synchronize its clock time whenever it
tunes to a radio station using RDS with CT signals.
1. When tuning to a station transmitting RDS data, the
RDS symbol will be shown on the display. Press and
hold the Menu/Info button.
2. Rotate the Tuning control knob until "RDS CT" and a
clock symbol appear on the display. Press the Tuning
control knob to enter the setting.
3. Rotate the Tuning control knob until "RDS CT"
appears on the display. Press the Tuning control knob
to confirm the setting. The clock time of the radio
will set up automatically according to the RDS data
received.
Note:
● The radio clock time will be valid for 5 days each time
the radio time is synchronized with RDS CT.
● To disable the RDS CT function, go back to step 1 to
2 and then rotate the Tuning control knob to select
"MANUAL" option. Press the Tuning control knob to
confirm the setting.
Setting the alarm clock
Your radio has two alarms which can each be set to
wake you to AM/FM radio or buzzer alarm. The alarms
may be set while the unit is in standby mode or while
playing.
Note:
Ensure that the time is set correctly before setting the
alarms. If no buttons are pressed for 10 seconds, the
radio will exit the alarm setup.
a. Setting radio alarm time:
1. The radio alarm can be set either when radio is on or
off.
2. Press and hold the radio alarm button, the radio
alarm symbol and the display hour will flash along
with a beep.
3. During radio alarm symbol flashes, rotate the Tuning
control knob to select the hour and press the Tuning
control knob again to confirm the hour setting. Then
rotate the Tuning control knob to select the minute
and press the Tuning control knob to confirm the
minute setting.
4. Rotate the Tuning control knob and the display will
show the frequency options for the alarm.
The alarm options are as follows:
ONCE – the alarm will sound once
DAILY – the alarm will sound everyday
WEEKDAY – the alarm will sound only on weekdays
WEEKEND – the alarm will sound only at weekends
Press the Tuning control knob to confirm the setting.
5. During radio alarm symbol is flashing, rotate the
Tuning control knob to select desired wake-up band
and station, then press the Tuning control knob to
confirm the selection.
6. Rotate the Tuning control knob to select the desired
volume and press the Tuning control knob to confirm
the volume. Radio alarm setting is now completed.
Note:
● If new radio alarm station is not selected, it will select
the last alarm station.
● If the selected AM/FM alarm station is not available
when the alarm is sounding, the buzzer alarm will be
used instead.
b. Setting HWS (Humane Wake System)
buzzer alarm:
A beep tone will activate when selecting the HWS
buzzer alarm.
The alarm beep will sound shorter every 15 seconds
for one minute followed by one minute silence before
repeating the cycle.
1. The buzzer alarm can be set either when the radio is
on or off.
2. Press and hold the buzzer alarm button, the symbol
and the display hour will flash along with a beep.
3. During buzzer alarm symbol flashes, rotate the
Tuning control knob to select the hour and press the
Tuning control knob again to confirm the hour setting.
Then rotate the Tuning control knob to select the
minute and press the Tuning control knob to confirm
the minute setting.
4. Rotate the Tuning control knob and the display will
show the frequency options for the alarm.
The alarm options are as follows:
ONCE – the alarm will sound once
12 ENGLISH