Maintenance / Checks; Terms Of The Warranty - Tuv nord NovoPort Instrucciones De Montaje, De Servicio Y De Mantenimiento

Operating Instructions
Before carrying out any work on the operator,
always pull out the mains plug!
All persons using the door system must be
shown how to operate it properly and safely.
When the operator is being used, the opening
and closing cycles must be monitored.
Keep hand transmitters out of the reach of
children.
It must be ensured that neither persons nor
objects are located within the door's range of
travel.
Functional sequence
The garage door operator can be actuated by
push-button on the control unit (figure 24) or by
other impulse generators, such as hand
transmitters, key switches etc. It is only necessary
to generate a short, sharp impulse.
Initial impulse:
The operator starts up and causes the door to
travel to the set OPEN or CLOSE end-of-travel
positions.
Impulse generated while the door is in motion:
The door stops.
A new impulse:
The door continues to move but in the opposite
direction.
Internal safety device
If the closing door encounters an obstruction, the
operator stops and causes the door to open to its
top end-of-travel position in order to clear the
obstruction.
During the last 2 seconds of the closing cycle, the
door only opens slightly, this being sufficient to
clear the obstruction but otherwise preventing
anyone from being able to see inside the garage.
If the opening door encounters an obstruction, the
operator stops immediately. The door can be
closed again be generating a new impulse.
Dear Customer,
During production the garage door operator you
have purchased has undergone various checks by
the manufacturer to ensure that it is of impeccable
quality. Should this operator or part of it prove to
be of no or limited use as a result of proven
material or manufacturing defects, we shall rectify
this, at our discretion, by means of a free-of-charge
repair or replacement.
We shall not accept any liability for damage as a
result of unsatisfactory fitting and installation,
improper putting into service, incorrect operation
and maintenance, excessive use or overloading as
Retain these installation, operating and maintenance instructions for the full duration of the operator's service life!
External safety devices
Wicket door contact (STOP A)
An open wicket door stops the operator
immediately or prevents it from starting up.
Photocell defective (STOP B)
If the photocell is interrupted while the door is
closing, the door stops and reverses direction. An
interruption while the door is opening has no effect.
Quick release
When altering settings or making adjustments, in
the event of a power failure or malfunctions, the
door can be disengaged from the operator by
actuating the pull cord with knob on the lifting arm
(figure 25a), so that it can be operated manually.
To restore power operation,
press down the lever on the motor head (figure
25b) and the operator re-engages.
If the door is to be operated manually over a longer
period of time, then the door latches which were
taken out of service for power operation, must be
refitted, otherwise the door will not be latched
when closed.
Lighting
The lighting switches on automatically whenever a
start impulse is generated and switches off again
after the set time phase (factory setting approx. 90
seconds).
A second button on the hand transmitter can be
programmed for 4-minutes light (figure 23). When
the button on the hand transmitter is pressed, the
light switches on independent of the motor and
switches off again after approx. 4 minutes.
Changing the light bulb:
Pull out the mains plug and open the lamp cover
using a Phillips screwdriver size 2 x 100. Replace
the light bulb (230 V, 40 W, cap E27) and screw
the lamp cover back on again.
Signal light
If a signal light for signalling the opening and
closing phases is installed, this flashes together
with the lamp in the operator as soon as a start

Terms of the Warranty

well as any alterations or modifications carried out
to the operator and accessory parts by the
customer.
The same shall also apply for damage incurred
during transit or as a result of force majeure,
external influences or natural wear as well as
special atmospherical stresses. We cannot accept
any liability following alterations or modifications of
functional parts carried out by the customer. We
must be notified of any defects immediately in
writing; on request, the parts in question shall be
sent to us.
impulse is generated. The operator starts with a
time delay in accordance with the set warning
phase (see Special Settings in menu stage 7).
Hand transmitters
Programming further hand transmitters:
See menu stages 1 and 2 (figures 22 and 23).
Changing the battery: Slide back the battery
compartment cover on the hand transmitter.
Take out the battery.
Insert a new battery (alkaline 23A, 12V). Be sure to
pole correctly! Slide the cover back on.
Empty batteries must be disposed of
separately (toxic waste)!

Maintenance / Checks

For your own safety we recommend
that the door system be checked by a
specialist after initial installation and
then regularly at intervals of 1 year
minimum.
Monitoring the force limit
The operator's control unit features a 2-processor
safety system to monitor the force limit.
The integral force cut-out is automatically tested at
each end-of-travel position.
The door system must be checked before being
put into service and at least once a year thereafter,
during the course of which, a check of the force
limit facility (figure 21) must also be carried out!
Caution! If the closing force is set too
high, persons can be placed at risk of
injury or property could get damaged.
The opening force can be re-adjusted in menu
stage 5, the closing force in menu stage 6.
We shall not bear the costs for dismantling and
installation, freight and carriage. If a complaint is
proven to be unjustified, the customer must bear
our costs.
This warranty is only valid in conjunction with the
signed invoice and commences on the day of
delivery. The manufacturer guarantees that the
product is free of defects.
The warranty is granted for a period of 24 months,
in as far as the verification overleaf has been
properly filled out. Otherwise the warranty shall
expire 27 months after the date of manufacture.
GB