Circuit Priming - Gaggia Milano CAREZZA Instrucciones De Uso

a steady jet of water flows out of the steam wand (Pan-
narello).
6
Close the "hot water/steam" knob (3) by turning it coun-
ter-clockwise. Remove the container.
The machine begins the warm-up phase only after the water
circuit has been correctly primed.
Note: if the knob is left open, the pump is
automatically disengaged after a few seconds
and the " " light (20) starts blinking.

4.6 Circuit Priming

When the water tank is empty, the machine circuit must be
primed again.
Note: if the machine has been operating without
water for a lot of time and the "
" " (20) and " " (18) lights are blinking, please refer
to the "Troubleshooting" table.
5
• Place a container under the steam wand (Pannarello).
• Open the "hot water/steam" knob (3) by turning it clock-
wise. The pump is activated automatically.
• Wait until a steady jet of water flows out of the steam
wand (Pannarello).
6
• Close the "hot water/steam" knob (3) by turning it
counter-clockwise. Remove the container.
Note: if the steam knob is opened by mistake
during the warm-up phase, the " " light
(20) starts blinking. Close the knob and wait until the
machine is ready.
4.7 Using the Machine for the First Time or
After a Period of Inactivity
This simple operation ensures an optimum brewing and must
be performed:
- at first start-up;
- when the machine remains inactive for a long time (more
than 2 weeks).
Dispensed water must be emptied into an
adequate drain. It is not suitable for food use. If
the container fills up during the cycle, stop dispensing
water and empty the container before resuming the
operation.
A 2
Rinse the water tank and refill it with fresh drinking
water. Insert the water tank back into its seat in the coffee
machine and make sure that it locks into place - its profile
should adhere to that of the coffee machine.
4219-450-03851 MANUAL GAG. V2 RI8525 GGBF US 1-3L.indd 17
B Turn on the machine by pressing the (11) button. Wait until
the " " light (14) turns on steady.
C 5
Place a container under the steam wand (Pannarello).
Open the knob (3) by turning it clockwise. The pump is ac-
tivated automatically.
D Dispense the whole water tank content from the steam/
hot water wand (Pannarello); to stop the dispensing pro-
cess, close the knob (3) by turning it counter-clockwise.
During this operation the pump is automatically
disengaged and the " " light (20) is blinking:
this is a normal behaviour of the machine. Close the
knob. Wait until the "
opening the knob again.
E 2
Fill the water tank with fresh drinking water. Insert
the water tank back into its seat in the coffee machine and
" (14),
make sure that it locks into place - its profile should adhere
to that of the coffee machine.
13 14
F Insert the filter holder (21) into the brew unit (4)
from the bottom. Turn the pressurized filter holder from
left to right until it locks into place. Release the pressurized
filter holder grip. The handle will turn slightly to the left.
This movement guarantees optimum filter holder perfor-
mance.
G 15
Place a suitable container under the filter holder.
H 17 Press the "
ter.
At the end of the process, stop the operation by pressing
the " " button.
I Repeat the operations described in step (H) until the wa-
ter tank is completely empty.
2
L Refill the water tank with fresh drinking water.
M 19
Remove the filter holder from the unit by turning it
from right to left and rinse it with fresh drinking water.
Now the machine is ready. Please see related chapters for
operating details on how to brew coffee and dispense steam.
5 Rinsing
Note: make sure the filter holder is inserted to
ensure a proper warm-up of the machine.
The machine is set so as to automatically rinse the coffee circuit
with fresh water every time it is turned on. This is conceived to
ensure the correct machine warm-up and an optimum coffee
aroma.
Place a container under the dispensing spout.
ENGLISH
" light (14) is steady on before
" button and dispense a cup of hot wa-
03/12/2018 15:45:34
17