Publicidad
Idiomas disponibles
Idiomas disponibles
void the warranty.
Do not swallow. If swallowed, call a physician
immediately. Keep out of reach of children. Store
away from heat or open flame.
CHECKING THE AUTOMATIC OILER
Proper functioning of the automatic oiler can be checked
by running the Chainsaw and pointing the tip of the
guide chain bar towards a piece of cardboard or paper on
the ground. If an increasing oil pattern develops on the
cardboard, the automatic oiler is operating fine. If there
is no oil pattern, despite a full oil reservoir, contact Worx
customer service agent or Worx approved service agent.
CAUTION: Do not touch the ground with the
chain. Ensure safety clearance of 16".
OPERATION
1. BEFORE USING YOUR CORDLESS TOOL
WARNING! The charger and battery pack are
specially designed to work together so do not
attempt to use any other devices. Never insert or allow
metallic objects into your charger or battery pack
connections because of an electrical failure and hazard
will occur.
NOTE: Your battery packs are shipped UNCHARGED and
you must charge once before use.
The battery charger supplied is matched to the Li-ion
battery installed in the machine. Do not use another
battery charger.
2. CHECKING THE BATTERY CHARGE CONDITION (See
Fig. G)
The battery level can be known from the battery indicator
light by pressing the button beside the lights.
Note: Fig. G only applies for the battery pack with battery
indicator light.
3. CHARGING YOUR BATTERY PACK (See Fig. H)
The Li-ion battery is protected against deep discharging.
When the battery is empty, the machine is switched off by
means of a protective circuit. Each battery must be fully
charged before the first use.
In a warm environment or after heavy use, the battery pack
may become too hot to permit charging. Allow time for the
battery to cool down before recharging.
Note: Always fully charge the two batteries at same time.
More details can be found in charger's manual.
4. TO REMOVE OR INSTALL BATTERY PACK (See Fig. I)
Depress the battery pack release button to remove the
2 battery packs from your tool. After recharging, insert
the 2 battery packs into the battery ports. A simple push
and slight pressure will be sufficient until a click is heard.
Check to see if the battery is fully secured.
Note:
When removing the battery pack, hold it firmly to
•
avoid dropping and injury.
This machine will only run when 2 batteries are
•
installed. It is recommended to use the same two
batteries and charge the two batteries at the
Cordless Chainsaw
same time.
When you use two batteries with different power,
•
the machine will only run to the lower common
denominator.
5. POWER INDICATOR LIGHT (See Fig. J)
MPORTANT:
When only one light is illuminated, your battery is
overly discharged, even though the machine may
still be capable to work. Continuing to operate
your machine with the battery in this discharged
condition may reduce the life and performance of
your battery.
When no light are illuminated, at least one battery
is not fully installed or battery may be defective,
please double check the batteries are fully seated
into position.
BATTERY STATUS
● Before starting or after use, press the button beside the
power indicator light on the machine to check the battery
capacity.
● During operation, the battery capacity will be indicated
automatically by the battery power indicator. The indicator
constantly senses and displays the battery condition as
follows.
● For the machine with 2 battery packs with different
power, the power indicator light displays the battery
condition with the lower one of the two batteries.
Battery indicator
Battery condition
light status
Five green lights
The two batteries are in a
(
) are
highly charged condition.
illuminated.
The two batteries have a
Two, three or four
remaining charge. The more
green lights are
lights are illuminated, the
illuminated.
more battery capacity.
The battery level of at least
Only one green
one battery pack is very low.
light (
) is
Please check and charge the
illuminated.
battery pack.
At least one battery is not fully
No light is
installed or battery may be
illuminated.
defective.
At least one battery is over
discharged (please refer to
Only one light is
the battery charge condition),
flashing twice per
please recharge the two
cycle.
batteries at once before use
again or storage.
Only one light is
At least one battery is hot, wait
flashing three times
for them cool down before
per cycle.
start again.
Only one light is
The machine is over load.
flashing four times
Remove tool from cutting area
per cycle.
and try again.
15
EN
Publicidad
