Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
1 – Introduction
Precautions for placement and use
0 The operating temperature range of this unit is 5–35 °C.
0 Do not install this unit in the following types of locations. Do-
ing so could make the sound quality worse or cause malfunc-
tion.
Locations with frequent vibrations
Near windows or other places exposed to direct sunlight
Near heaters or other extremely hot places
Extremely cold places
Very humid or poorly ventilated places
Very dusty places
0 Install the unit so that it is level.
0 To enable good heat dissipation, do not place anything on
top of the unit.
0 Do not place the unit on top of a power amplifier or other de-
vice that generates heat.
Notes about power supplies
0 Insert the included power cord all the way into the AC IN con-
nector.
0 Do not connect a power supply other than one that is
AC100V - 240V (50/60Hz).
0 Hold the power cord by its plug when connecting or discon-
necting it.
Beware of condensation
Condensation could occur if the unit is moved from a cold place
to a warm place, it is used immediately after a cold room has
been heated or it is otherwise exposed to a sudden temperature
change.
To prevent this, or if this occurs, let the unit sit for one or two
hours at the new room temperature before using it.
Cleaning the unit
Use a dry soft cloth to wipe the unit clean. Do not wipe with
chemical cleaning cloths, thinner, alcohol or other chemical
agents. Doing so could damage the surface or cause discolor-
ation.
About compact discs
In addition to commercially-available music CDs, this unit can
play CD-R and CD-RW discs recorded in the audio CD (CD-DA)
format as well as CD-R and CD-RW discs that contain MP3 audio
files.
CAUTION
8cm CDs cannot be used. If an 8cm CD is inserted, it will au-
tomatically be ejected. During ejection, if it stops at a place
where it cannot be removed, press and hold the EJECT but-
ton.
Precautions for use
0 Always insert discs with the label facing upward.
10
TASCAM CD-400U
0 To remove a disc from its case, press down on the center of
the disc holder, then lift the disc out, holding it carefully by
the edges.
0 Do not touch the signal side (the unlabeled side). Finger-
prints, oils and other substances can cause errors during play-
back.
0 If fingerprints or dust adhere to the signal recording side of
a disc, wipe gently with a soft dry cloth from the center to-
wards the outside edge.
0 Dirt on discs can lower the sound quality, so clean them and
always store them in a clean state.
0 Do not use any record spray, anti-static solutions, benzene,
paint thinner or other chemical agents to clean CDs as they
could damage the delicate playing surface. It may cause CDs
to become unplayable.
0 Do not apply labels or other materials to discs. Do not use
discs that have had tape, stickers or other materials applied
to their surface. Do not use discs that have sticky residue
from stickers, etc. Such discs could become stuck in the unit
or cause it to malfunction.
0 Never use a commercially available CD stabilizer.
0 Using stabilizers with this player will damage the mechanism
and cause it to malfunction.
0 Do not use cracked discs.
0 Only use circular compact discs. Avoid using non-circular pro-
motional, etc. discs.
0 Copy Control CDs have been sold by several record compa-
nies in an attempt to protect their copyrights. Since some of
these discs do not comply with the CD specifications, they
may not be playable on the unit.
Slot loading of discs
1.
As shown in the illustration, hold the disc with the labeled
side up and insert it part way into the slot.
2.
Push the disc in further until just before it disappears. It will
automatically be drawn in to the slot.
If a disc will not load properly
If a disc becomes stuck during insertion, for example, and is diffi-
cult to push, do not try to force the disc in. Pull the disc out once,
press the EJECT button, and then try inserting it again. (Trying
to force the disc in could damage the unit.)
Publicidad
Capítulos
Tabla de contenido
Solución de problemas
