ENGLISH
Problem
Possible solution
Mower doesn't run when
Check to make sure mower is properly plugged
bail handle is activated.
in and that the button on switch box is being
completely depressed before pulling the bail
handle.
Release bail handle to turn mower off. Remove
battery pack, turn mower over and check that
blade is free to turn.
Check that the battery cavity is free of debris
and is connected properly.
Has battery been fully charged? Press state of
charge button.
Motor stops while mowing.
Release bail handle to turn mower off. Remove
battery pack Turn mower over and check that
blade is free to turn.
Raise cutting height of wheels to highest posi-
tion and start mower.
Check that the battery cavity is free of debris
and is connected properly
Has battery been fully charged? Press state of
charge button
Avoid overloading the mower. Slow down the
cutting pace, or raise the cut height.
Mower runs but cutting
Release bail handle to turn mower off. Unplug
performance is unsatisfac-
mower. Turn mower over and check:
tory,
u
u
Wheel height adjustment may be set too low for
grass condition. Raise cutting height.
Mower is too hard to push.
Release bail handle to turn mower off. Unplug
mower. Raise cutting height to reduce deck
drag on grass. Check each wheel for free
rotation
Mower is abnormally noisy
Release bail handle to turn mower off. remove
and vibrates.
battery pack. Turn mower on side and check
blade to ensure it has not been bent or
damaged. If blade is damaged, replace with
a BLACK+DECKER replacement blade. If
the underside of the deck is damaged, return
mower to a BLACK+DECKER Authorized
service center.
If there is no visible damage to the blade and
the mower still vibrates:
u
u
u
u
u
If mower still vibrates, return the mower to
an authorized BLACK+DECKER authorized
service center.
Battery charger LEDs
Check plug connection.
not on.
Replace charger.
Mower not picking up
Chute clogged. Release bail handle to turn
clippings with bag.
mower off. Remove battery pack. Clear chute of
grass clippings.
Raise cutting height of wheels to shorten length
of the cut.
Bag full. Empty bag more often.
Protecting the environment
14
(Original instructions)
Blade for sharpness - Keep blade sharp.
Deck and discharge chute for clogging.
Release bail handle to turn mower off.
Remove battery pack.
Disassemble entire blade assembly as
described in the "Removing and installing
blade" section.
Remove any debris and clean each piece.
Replace each piece as described in the
"Removing and installing blade" section.
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Voltage
Vdc
-1
min
No-Load Speed
kg
Weight
Blade length
cm
Batteries
Cat#
Cat#
Vdc
Ah
Weight Kg
Amps
BL1518
18
1.5
0.38
BL1518
BL1518ST
18
1.5
0.38
BL1518ST
BL2018
18
2.0
0.39
BL2018
BL2018ST
18
2.0
0.39
BL2018ST
BL2518
18
2.5
0.43
BL2518
BL4018
18
4.0
0.64
BL4018
BL5018
BL5018
18
5.0
0.7
BL20362
36
2.0
0.64
BL20362
BL2536
36
2.5
0.68
BL2536
BL1554
18/54
1.5
1.08
BL1554
BL2554
18/54
2.5
1.2
BL2554
Hand/arm weighted vibration value:
= <2.5 m/s
, uncertainty (K) = 1.5m/s
2
L
(sound preasure) 74.5 dB(A)
PA
uncertainty (K) = 2.5 dB(A)
L
(sound power) 86 dB(A)
WA
uncertainty (K) = 1.5 dB(A)
EC declaration of conformity
MACHINERY DIRECTIVE
%
OUTDOOR NOISE DIRECTIVE
BCMW3318, BCMW3336 lawn mower
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60335-1:2012 + A11:2014,
EN 60335-2-77:2010
BCMW3318
BCMW3336
18V
3800RPM
3800RPM
15
33
Chargers (minutes)
90590287*
N517388*
BDC1A
BDC2A
BDC2A36
400mA
1A
1A
2A
225
90
90
45
225
90
90
45
300
120
120
60
300
120
120
60
380
150
150
75
600
240
240
120
750
300
300
135
X
X
X
X
X
X
X
X
225
90
90
45
380
150
150
75
.
2
36V
15
33
1.35A
X
X
X
X
X
X
X
90
110
X
X