Publicidad
Idiomas disponibles
Idiomas disponibles
2
PRODUCT DESCRIPTION
2.1
Components
The product consists of the following main components and
elements:
Fig. 2.1
A
Rotating flange
B
Wall bracket
1
C Hose tube
D Hood, incl. control valve
Fig. 2.1
Main components and elements
2.2
Operation
The welding fume is extracted through the hood of the arm by
a single or central fan. The extraction arm discharges the
polluted air to an extraction duct with filter unit or directly to
the atmosphere.
The hood of the arm is fitted with a control valve to shut off or
regulate the airflow. The valve is mostly used when several
extraction arms are integrated in a line installation; in such
configurations closing the valve prevents the loss of costly
heated air.
3
SAFETY
General
The manufacturer does not accept any liability for
damage to the product or personal injury caused by
ignoring of the safety instructions in this manual, or
by negligence during installation, use, maintenance, and repair
of the product mentioned on the cover of this document and
any corresponding accessories. Specific working conditions or
used accessories may require additional safety instructions.
Immediately contact your supplier if you detect a potential
danger when using the product.
The user of the product is always fully responsible
for observing the local safety instructions and
regulations. Observe all applicable safety
instructions and regulations.
User manual
- Everyone working on or with the product, must be familiar
with the contents of this manual and must strictly observe
the instructions therein. The management should instruct the
H types only
86958016
A
B
C
D
personnel in accordance with the manual and observe all
instructions and directions given.
- Do not change the order of the steps to perform.
- Keep the manual with the product.
Users
- The use of this product is exclusively reserved to authorised,
trained and qualified users. Temporary personnel and
personnel in training can only use the product under
supervision and responsibility of skilled engineers.
- Stay alert and keep your attention to your work. Do not use
the product when you are under the influence of drugs,
alcohol or medicine.
- The product is not to be used by children or persons with
reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given
supervision or instruction.
- Children must be supervised not to play with the product.
Intended use
2
The product has been designed exclusively for extracting
fumes and particles which are released during the most
common welding and cutting processes. Using the product for
other purposes is considered contrary to its intended use. The
manufacturer accepts no liability for any damage or injury
resulting from such use. The product has been built in
accordance with state-of-the-art standards and recognised
safety regulations. Only use this product when in technically
perfect condition in accordance with its intended use and the
instructions explained in the user manual.
Technical specifications
Do not change the specifications given in this manual.
Modifications
Modification of (parts of) the product is not allowed.
Product combinations
If the product is used in combination with other products or
machines, the safety instructions in the documentation of
these products also apply.
Installation
- The installation of this product is exclusively reserved to
authorised, trained and qualified engineers.
- During installation, always use Personal Protective
Equipment (PPE) to avoid injury. This also applies to persons
who enter the work area during installation.
- Use sufficient climbing gear and safety guards when working
on a higher level than 2 metres (local restrictions may
apply).
- Do not install the product in front of entrances and exits
which must be used for emergency services.
- Mind any gas and water pipes and electric cables.
- Make sure that the workspace is well illuminated.
- Stay alert and keep your attention to your work. Do not
install the product when you are under the influence of
drugs, alcohol or medicine.
- Air containing particles such as chromium, nickel, beryllium,
cadmium, lead etc., should never be recycled. This air must
always be brought outside the working area.
1.
"Intended use" as explained in EN-ISO 12100-1 is the use for which the
technical product is suited as specified by the manufacturer, inclusive of his
directions in the sales brochure. In case of doubt it is the use which can be
deduced from the construction, the model and the function of the technical
product which is considered normal use. Operating the machine within the
limits of its intended use also involves observing the instructions in the user
manual.
EN | 3
Publicidad
