Publicidad
Idiomas disponibles
Idiomas disponibles
Use
WARNING!
Fire hazard! Do not use the product for:
- polishing applications in combination with
grinding, welding or any other application that
generate sparks
are highly flammable and pose a high risk of filter fires when
exposed to sparks)
- arc-air gouging
- extracting flammable, glowing or burning particles
or solids or liquids
- extracting of aggressive fumes (such as
hydrochloric acid) or sharp particles
- sucking cigarettes, cigars, oiled tissues, and other
burning particles, objects, and acids
WARNING!
Explosion hazard! Do not use the product for
explosion-hazardous applications, e.g.:
- aluminium laser cutting
- grinding aluminium and magnesium
- explosive environments or explosive substances/
gases
WARNING!
Do not use the product for:
- extraction of hot gases (more than 70°C/158°F
continuously)
- flame spraying
- extraction of cement, saw dust, wood dust etc.
•
Inspect the product and check it for damage. Verify the
functioning of the safety features.
•
During use, always use Personal Protective Equipment
(PPE) to avoid injury. This also applies for persons who
enter the work area.
•
Check the working environment. Do not allow unauthorised
persons to enter the working environment.
•
Protect the product against water and humidity.
•
Make sure the room is always sufficiently ventilated; this
applies especially to confined spaces.
•
Make sure that the workshop, in the vicinity of the product,
contains sufficient approved fire extinguishers (suitable for
fire classes ABC).
Service, maintenance and repairs
•
Obey the maintenance intervals given in this manual.
Overdue maintenance can lead to high costs for repair and
revisions and can render the guarantee null and void.
•
Always use Personal Protective Equipment (PPE) to avoid
injury. This also applies for persons who enter the work
area.
•
Make sure the room is sufficiently ventilated.
•
Use tools, materials, lubricants and service techniques
which have been approved by the manufacturer. Never use
worn tools and do not leave any tools in or on the product.
•
Safety features which have been removed for service,
maintenance or repairs, must be put back immediately
after finishing these jobs and it must be checked that they
still function properly.
•
Use sufficient climbing gear and safety guards when
working on a higher level than 2 metres (local restrictions
may apply).
•
Clean the area afterwards.
ATTENTION
Service, maintenance and repairs must be
performed in accordance with directive TRGS 560
and TRGS 528 by authorised, qualified and trained
persons (skilled) using appropriate work practices.
86958016
(fibers from polishing or abrasive flap disks
Personal protective equipment (PPE)
Wear respiratory protection and protective
gloves during service, maintenance and
repairs.
4
INSTALLATION
4.1
Tools and requirements
You need the following tools and requirements to
install the product:
- basic tools
4.2
To be sourced locally
You need the following material to install the
product:
- wall mounting hardware
4.3
Unpacking
Make sure that the product is complete. The
package contains:
- extraction arm (pre-assembled; excl. hose tube)
- hose tube
- hose clamp (2)
- rotating flange
- arm swivel ring, incl. rubber collar
- extraction hood
- hood collar with safety mesh
- washer M20
Additionally for "H" types:
- wall bracket (with integrated rotating flange)
- hexagon bolt M6x25 (4)
If parts are missing or damaged, contact your supplier.
There are different ways to install the EcoFlex arm.
The table below gives a summary of the relevant
paragraphs per arm type (specifically H and S) and
the preferred mounting sequence.
HANGING MOUNTING
EcoFlex H
Wall
1. Start with
par. 4.4.1
2. Arm mounting
par. 4.4.3
3. Fan mounting
par. 4.4.4
4. Hood mounting
par. 4.6
STANDING MOUNTING
EcoFlex S
Stanchion
1. Start with
par. 4.5.1
2. Hood mounting
par. 4.6
For mounting of the EcoFlex H (hanging):
•
proceed with paragraph 4.4
For mounting of the EcoFlex S (standing):
•
proceed with paragraph 4.5
2.
The type of hardware depends on the wall type
3
Stanchion
Ext. crane
par. 4.4.2
INS_
Extension
par. 4.4.3
par. 4.4.3
par. 4.4.4
-
par. 4.6
par. 4.6
Wall bracket Mobile unit
par. 4.5.2
par. 4.5.3
par. 4.6
par. 4.6
EN | 4
Publicidad
