Publicidad
Idiomas disponibles
Idiomas disponibles
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect con-
ditions.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
5. Before starting the equipment
5.1 Appliance assembly
Fitting the appliance head (Fig. 1, 4/3)
The appliance head (3) is fastened to the con-
tainer (7) by the locking hook (6). To remove the
appliance head (3), open the locking hook (6) and
remove the appliance head (3). When fi tting the
appliance head (3), make sure that the locking
hook (6) locks into place correctly.
Fitting the castors (Fig. 5/13)
Fit the castors (13) into the appropriate mountings
on the underside of the tank (7). Push the castors
(13) fi rmly into the mounting until they engage
with a clicking noise (Fig. 5).
Anl_SA_TC_VC_18_20_Li_S_Solo_SPK8.indb 24
Anl_SA_TC_VC_18_20_Li_S_Solo_SPK8.indb 24
GB
5.2 Fitting the fi lter
Notice!
Never use the wet and dry vacuum cleaner wit-
hout a fi lter!
Always ensure that the fi lters are perfectly secure!
Fitting the foam fi lter (Fig. 6/15)
For wet-vacuuming, slip the supplied foamed
plastic fi lter (15) over the fi lter basket.
Fitting the pleated fi lter (Fig. 7)
For dry-vacuuming, slip the pleated fi lter (18) over
the fi lter basket (Fig. 3/4). The pleated fi lter is sui-
table for dry-vacuuming only.
Assembling the dirt bag (Fig. 9/14)
For vacuuming fi ne, dry dirt it is recommended
that you fi t the dirt bag (14). Slip the dirt bag (14)
over the vacuuming hole. The dirt bag (14) is sui-
table for dry-vacuuming only. The dirt bag makes
it easier to dispose of the sucked-in dust.
5.3 Fitting the suction hose (Fig. 3, 10, 11)
Connect the suction hose (10) to the correspon-
ding connector on the wet and dry vacuum clea-
ner, depending on the application required.
Vacuuming
Connect the suction hose (10) to the suction hose
connector (8)
Blowing
Connect the suction hose (10) to the blow con-
nector (9)
One or more of the elements which make up the
3-part suction tube (11) can be attached to the
suction hose (10) to extend it. The adapter (17)
must be inserted between the suction tube (11)
and the combination nozzle (12) or crevice nozzle
(16).
5.4 Suction nozzles
Dual-purpose nozzle (Fig. 2)
The dual-purpose nozzle (12) is for vacuuming
solids and liquids over medium to large areas.
Various attachments can be fi tted to the combi-
nation nozzle depending on what you sort of work
you wish to carry out:
Crevice nozzle (Fig. 2)
The crevice nozzle (16) is designed for vacu-
uming solids and liquids in corners, edges and
other areas that are diffi cult to access.
- 24 -
22.03.2018 14:15:31
22.03.2018 14:15:31
Publicidad
