Publicidad
Do not weld on drums or any closed containers.
1-1. Additional Safety Symbols And Definitions
?
Some symbols are found only on CE products.
2-1.
Símbolos y definiciones adicionales de seguridad
�
Algunos símbolos se encuentran únicamente en los productos con la marca CE.
Do not weld on drums or any closed containers.
?
Read Owner's Manual and inside labels for connection points and procedures.
= < 60
Read Owner's Manual and inside labels for connection points and procedures.
Keep your head out of the fumes
Wear dry insulating gloves. Do not wear wet or damaged gloves.
Wear dry insulating gloves. Do not wear wet or damaged gloves.
Use coolant suggested by the manufacturer.
Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves.
SECCIÓN 2 – DEFINICIONES
Do not weld on drums or any closed containers.
Falling unit can cause injury and damage. Do not move unit where two wheels are at a different height and unit
could tip
avoid tipping. Be careful when moving unit over uneven surfaces.
Protect yourself from electric shock by insulating yourself from work and ground.
Warning! Watch Out! There are possible hazards as shown by the symbols.
Do not cut on drums or any closed containers.
Do not stack racks. Lift only with proper equipment and correct procedures.
Do not discard product (where applicable) with general waste.
Reuse or recycle Waste Electrical and Electronic Equipment (WEEE) by disposing at a designated collection
Protect yourself from electric shock by insulating yourself from work and ground.
facility.
Moving parts can injure.
Do not grip material near cutting path.
Contact your local recycling office or your local distributor for further information.
Disconnect input plug or power before working on machine.
Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves.
Always connect green, Or green with yellow stripe, wire to supply grounding terminal.
Turn off power before disassembling torch.
Connect black, white, and red wires (L1, L2, L3) to line terminals.
Keep your head out of the fumes.
Pinch points can injure.
Do not remove or paint over (cover) the label.
3
Protect yourself from electric shock by insulating yourself from work and ground.
Recycle.
Keep your head out of the fumes
Protect yourself from electric shock by insulating yourself from work and ground.
Use coolant suggested by the manufacturer.
Become trained and read the instructions before working on machine.
Use forced ventilation or local exhaust to remove the fumes.
3
Disconnect input plug or power before working on machine.
Falling unit can cause injury. Do not move or operate unit where it could tip.
Connect green or green/yellow grounding conductor to ground terminal.
Use forced ventilation or local exhaust to remove the fumes.
Keep your head out of the fumes.
Keep your head out of the fumes
Use forced ventilation or local exhaust to remove the fumes.
Use forced ventilation or local exhaust to remove the fumes.
line terminals.
Engine fuel plus flames or sparks can cause fire.
Become trained and read the instructions before working on the
machine or welding.
Remove unit from shipping crate. Remove Owner's Manual from un
Follow instructions to install muffler.
¡Advertencia! ¡Cuidado! Existen peligros potenciales indicados por
los símbolos.
Wear hat and safety glasses. Use ear protection and button shirt
No deseche el producto (si fuese necesario) con los residuos
Hazardous voltage remains on input capacitors after power is turned
collar. Use welding helmet with correct shade of filter. Wear complete
comunes.
off. Do not touch fully charged capacitors. Always wait
body protection.
Read Owner's Manual. Read labels on unit.
Reutilice o recicle los residuos de aparatos eléctricos y electrónicos
after power is turned off before working on unit, AND check input ca-
(WEEE) desechándolos en una planta de recolección designada para
pacitor voltage, and be sure it is near 0 before touching any parts.
tal fin.
Si necesita mayor información, comuníquese con la oficina de reci-
clado de su localidad o con su distribuidor local.
Become trained and read the instructions before working on the
Move jumper links as shown on inside label to match input voltage
machine or welding.
job site. Include extra length in grounding conductor and connect
Hazardous voltage remains on input capacitors after power is turned
grounding conductor first. Connect line input conductors as shown
off. Do not touch fully charged capacitors. Always wait
Desconecte el enchufe de la entrada o la alimentación antes de tra-
inside label. Double-check all connections, jumper link positions, an
power is turned off before working on unit, AND check input capacitor
bajar en la máquina.
input voltage before applying power.
voltage, and be sure it is near 0 before touching any parts.
Wear hat and safety glasses. Use ear protection and button shirt
collar. Use welding helmet with correct shade of filter. Wear complete
Move jumper links as shown on inside label to match input voltage at
Always lift and support unit using both handles. Keep angle of lifting
body protection.
job site. Include extra length in grounding conductor and connect
device less than 60 degrees.
Plugged filter or hoses can cause overheating to the power source
grounding conductor first. Connect line input conductors as shown on
and torch.
inside label. Double-check all connections, jumper link positions, and
Use a proper cart to move unit.
No quite esta etiqueta ni la cubra con pintura.
input voltage before applying power.
Every 100 hours, check and clean filter and check condition of hos
Engine fuel plus flames or sparks can cause fire.
Close door before turning on unit.
Reciclable.
Move jumper links as shown on inside label to match input voltage at
job site. Include extra length in grounding conductor and connect
grounding conductor first. Connect line input conductors as shown on
Remove unit from shipping crate. Remove Owner's Manual from unit.
Read the Owner's Manual before working on this machine.
inside label. Double-check all connections, jumper link positions, and
Follow instructions to install muffler.
Use el refrigerante sugerido por el fabricante.
input voltage before applying power.
Si necesita mayor información acerca de la seguridad en la soldadu-
Read the labels on the welding power source, wire feeder, or other
Read Owner's Manual. Read labels on unit.
Close door before turning on unit.
ra, lea las etiquetas adheridas a la máquina de soldar, el alimentador
major equipment for welding safety information.
Become trained and read the instructions before working on the
de alambre y otros equipos.
machine or welding.
Move jumper links as shown on inside label to match input voltage at
Welding current creates an electric and magnetic field (EMF)
job site. Include extra length in grounding conductor and connect
around the welding circuit and welding equipment.
Read the Owner's Manual before working on this machine.
grounding conductor first. Connect line input conductors as shown on
Become trained and read the instructions before working on the
Lea el manual del usuario antes de trabajar en esta máquina.
Connect input conductors (L1, L2 And L3) to line terminals.
inside label. Double-check all connections, jumper link positions, and
machine or cutting.
input voltage before applying power.
Read the labels on the welding power source, wire feeder, or other
Plugged filter or hoses can cause overheating to the power source
major equipment for welding safety information.
Filtros o mangueras obstruidos pueden causar recalentamiento a la
and torch.
Remove unit from shipping crate. Remove Owner's Manual from unit.
fuente de poder y a la antorcha.
Follow instructions to install muffler.
Welding current creates an electric and magnetic field (EMF)
around the welding circuit and welding equipment.
Every 100 hours, check and clean filter and check condition of hoses.
Every 100 hours, check and clean filter and check condition of hoses.
Cada 100 horas revise y limpie el filtro, y revise el estado de las
mangueras.
During the first 50 hours of operation keep welding load above 200
amperes. Do not weld below 200 amperes of output.
Safe15 2012
Safe97 201
Safe64 2017 04
Safe2 201
Safe45 201
Safe16 201
Safe98 201
Safe65 2012 06
Safe46 201
Safe3 201
Safe1 2012
Safe17 201
Safe99 201
60 seconds
Safe64 2017 04
Safe66 2012 06
Safe47 201
Safe37 2017
Safe42 2017 04
Safe4 201
Safe18 201
Safe100 201
5 minutes
after
Safe65 2012 06
Safe49 201
Safe43 2017 04
Safe67 2012 06
Safe5 201
Safe2 2017
Safe19 201
Safe101 201
Safe66 2012 06
Safe44 2012 05
Safe50 201
Safe68 2012 06
Safe6 201
Safe102 201
Safe20 201
Safe3 2017
Safe67 2012 06
Safe45 2012 05
Safe51 201
Safe69 2012 06
Safe7 201
Safe103 201
Safe4 2017
Safe46 2012 05
Safe68 2012 06
Safe52 201
Safe70 2012 06
Safe8 201
Safe104 201
Safe7 2017 04
Safe5 2017
Safe47 2012 05
Safe53 201
Safe71 2012 06
Safe69 2012 06
Safe9 201
Safe105 201
Safe6 2017
Safe40 2012 05
Safe72 2012 06
Safe49 2012 05
Safe70 2012 06
Safe 106 201
Safe41 2012 05
Safe7 2017
Safe71 2012 06
Safe73 2017 04
Safe50 2012 05
Safe46 2012 05
Safe8 2012
Safe72 2012 06
OM-
Safe51 2012 05
Safe51 2012 05
Safe9 2012
OM-628 Página 3
Safe73 2017 04
Safe52 2012 05
O
Publicidad
