Dynamic Range Control; Speaker Settings - Yamaha BD-S1900 Manual De Instrucciones

Settings
Note
– When "Secondary Audio" is set to "On", PCM is
automatically selected as the audio output mode.
When you selected "Digital Output"
Bitstream*:
– Select this when connecting to SURROUND
equipment with a built-in decoder for DOLBY
DIGITAL, etc.
– Setting to Bitstream will output each audio
signal by Bitstream.
PCM:
– Select this when connecting to 2 channel
stereo audio equipment.
– Setting to PCM will output by converting each
audio signal into PCM 2 channel audio signal.
Note
– See page 38 for information on the audio output
formats.

Dynamic Range Control

This lets you adjust the range between the loudest and
softest sounds (dynamic range) for playback at average
volume. Use this when it is hard to hear dialog.
Normal:
The same audio output range is played as the
original recorded audio output range.
Shift: When Dolby Digital audio is played back, the
dynamic range of the audio is adjusted so that the
dialog portion can be heard easily. (If the audio
sounds abnormal, set to "Normal".)
Auto*: When you play back audio in the Dolby TrueHD
format, the dynamic range is automatically
adjusted.
* Lower the audio volume before setting. If you do not do so, the
speakers may emit a loud sound or excessive output may be applied
to the speakers.

■ Speaker Settings

This sets size, distance, and volume levels for individual
speakers when you connect using AUDIO OUT (8ch
discrete) jacks.
1 Press SETUP to display the Setup Menu screen.
2 Press
/ / /
ENTER.
3 Press
/ to select "Speaker Settings", then press
ENTER.
4 Press
to select "Yes", then press ENTER.
/
– Select "No" to cancel without configuring the
Speaker Settings.
Audio output can be set according to the connected
amplifler and speaker systems.
(When 7.1ch output terminal is not used, it is not necessary
to set it.)
Do you want to adjust the speaker settings?
Yes
32
En
to select "Settings", then press
No
5 Press
/ / /
configure, then press ENTER.
L (Front Left), C (Center), R (Front Right), RS
(Surround Right), RB (Surround Back Right), LB
(Surround Back Left), LS (Surround Left), SW
(Subwoofer)
Set the speaker size, distance from listening point, and the sound
level to each speakers. Select speaker.
0dB
SW
12ft/+1dB
L
LS
LB
6ft/ 0dB 6ft/ 0dB
Test Start
6 Press
/ to select "Size", "Distance", and
"Level", then press
selected item.
Size: You can set the sizes from "Small", "Large*", and
"No".
Distance:
You can set the distances from "0.3m (1 ft)" -
"3.0m (10 ft)*" - "9m (29 ft)".
Level:
You can set the volume levels from "–12 dB" -
"0 dB*".
Notes
– When "SW" is set to "No", the speakers cannot be
set to "Small".
Set the speaker size, distance from listening point, and the sound
level to each speakers.
0dB
SW
12ft/ 0dB
L
LS
LB
6ft/ 0dB 6ft/ 0dB
Size
Small
– To set the other items, repeat step 6.
– To set the other speakers, repeat step 5 - 6.
7 Press
to select "Test Start", then press ENTER.
The test tone is output from each speaker to help you
judge the volume levels.
8 Press
to select "Test Tone Stop", then press
ENTER.
The test tone stops.
9 Press
to select "Finish", then press ENTER.
to select a speaker you want to
12ft/ 0dB
12ft/ 0dB
C
R
RS
RB
6ft/ 0dB 6ft/ 0dB
Finish
/ to set the value for the
12ft/ 0dB
12ft/ 0dB
C
R
RS
RB
6ft/ 0dB 6ft/ 0dB
Distance Level
12ft 0dB