Publicidad
Idiomas disponibles
Idiomas disponibles
Power Tool Use and Care
• Do not force the power tool. Use the correct power tool for your
application. It will do the job better and safer at the rate for which
it was designed.
• Do not alter or misuse the power tool. Use of the power tool
for operations different from those intended could result in a
hazardous situation.
• Do not use the power tool if the switch does not turn it on
or off. A power tool that cannot be controlled with the switch is
dangerous and must be repaired.
• Do not fire if the staples/nails are jammed. This will cause
damage to the driver blade and could invite accidents.
• Keep fingers off the trigger until ready to drive staple/nail.
• Do not use on hard surfaces such as rock, concrete, masonry,
bricks or steel. Personal injury or damage to the power tool
could result.
• Secure work. Use clamps or other practical ways to secure and
support the work piece to a stable platform. Holding the work by
hand or against your body is unstable and may lead to loss
of control.
• Store power tools. When not in use, all power tools should be
stored in a dry, locked cupboard and out of the reach of children
and other untrained persons.
• Check for damaged parts. Check for misalignment or bending
of moving parts, breakage of parts and any other condition that
may affect the power tools operation. If damaged, immediately
discontinue use and ensure the power tool is repaired before
using again. Poorly maintained power tools can result in
accidents.
• Maintain power tools with care. Cables must be checked at
regular intervals and replaced if damaged.
• Recommended accessories. Use only accessories that are
recommended by the manufacturer for your model. Accessories
that may be suitable for one tool may create a risk of injury when
used on another tool.
• Keep the power tool and its handle dry, clean and free from
oil and grease for the best and safest performance. Always use
a clean cloth when cleaning. Never use brake fluids, gasoline,
petroleum-based products, or any strong solvents to clean your
power tool. Following this rule will reduce the risk of loss of
control and deterioration of the power tool housing.
• Beware of hidden danger. Always make sure there is no danger
of hitting any hidden power cables, water or gas pipes.
Specific Safety Instructions
• Always assume the tool is loaded with fasteners. Handling the
tool without care could result in an unexpected firing of fasteners
and lead to personal injury.
• Use only the nails/staples specified in the manual. Use of
accessories that are not designed for this tool could result in
personal injury and/or damage to the power tool.
• Do not touch any parts of the power tool magazine or nose
during operation. Hold only by the handle or housing of the tool.
• Do not activate the power tool unless it is in contact with the
work piece. Serious injury can result if you depress the safety
contact nose with your fingers, or by improper operation.
• Fastening thin items. Special caution must be taken for possible
penetration through thin items, as this could cause possible harm
to anyone or anything behind the work piece or immediate area.
• Never use the tool as a hammer. The sudden impact could
shift inner components of the power tool, resulting in a fastener
discharge and injury.
• When fastening has been completed always disconnect the
power tool from the power source and unload the magazine.
6
Electric stapler-nailer_manual_PRINT.indd 6
Electric stapler-nailer_manual_PRINT.indd 6
• Do not disassemble or block any parts of the fastener
driving parts.
• Prior to each operation, check that the safety and trigger
mechanism is functioning properly.
• Never point any power tool at yourself or at any other person.
While working, hold the tool in such a way that no injuries can be
caused to the head or to the body in the event of possible recoil.
• Never actuate the power tool into free space or the air.
Fasteners can penetrate thin work pieces or slip off corners and
edges of the work piece, potentially putting people at risk.
• Do not drive fasteners on top of other fasteners.
• If a fastener jams, disconnect the power tool from the power
source. The mechanism may be under compression and a
jammed fastener may be discharged while attempting to free it.
• Do not use this tool to fasten electric cables. This tool is not
designed for the installation of electric cabling and may damage
electric cables which could lead to injury by electric shock or
fire hazards.
• Use appropriate detectors to determine if any utility lines
Cd
(electric, gas or water) are hidden within the work area or call
your local utility company for assistance.
Cd
• The electric motor has been designed for one voltage only.
Using an Extension Cable/Lead
An extension lead should not be used unless absolutely necessary.
If essential, use an approved extension cable suitable for the power
input of your tool (see technical data). The minimum conductor size
is 1mm
, the maximum length is 30 metres.
2
Model and Serial No.
The model name and serial number of this tool will be found on a
label located on the tool's housing. Please record the model name
and serial number in the space provided below. Please always give
the following information when contacting us:
MODEL NAME ......................................................................
Cd
SERIAL NUMBER ..................................................................
Explanation of Label on Power Tool
Li-ion
Cd
Always observe the safety instructions and warnings
Wear CE or UKCA approved safety goggles
at all times
Read instruction manual before use
Dispose of power tool in accordance with
environmental legislation
Conforms with UK Conformity Assessed Standards
Conforms with EC directives
Conforms with German Product Safety Act
Protection Class II: This product is double insulated
01/03/2023 10:28
01/03/2023 10:28
Publicidad
