Ryobi PBLHTS01 Manual Del Operador página 9

WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
APPLICATIONS
You may use this product for the purpose listed below:
„ Wet or dry cross cutting, rip cutting, and bevel cutting of
man-made tile, pavers, and natural stone tile materials
INSTALLING/REMOVING THE BATTERY PACK
See Figure 3, page 14.
„ Insert the battery pack into the product as shown.
„ Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured in the
saw before beginning operation.
„ Depress the latches to remove the battery pack.
For complete charging instructions, see the operator's
manuals for your battery pack and charger.
WARNING:
Battery tools are always in operating condition. Therefore,
switch should always be locked when not in use or car-
rying at your side.
ATTACHING SAW TO A VACUUM OR DUST BAG
See Figure 4, page 14.
When dry cutting, connect a vacuum cleaner hose or dust
bag to the dust chute for easy dust removal and disposal.
The dust port fits vacuum hoses 1-1/4 in. and 1-7/8 in.
NOTE: For dry cutting, leave water bottle installed or place
dust chute cap over empty water port to prevent dust and
debris from clogging the water supply system.
„ Remove the battery.
„ Remove dust chute cap from dust chute.
NOTE: If removing water bottle from saw while dry cutting,
insert dust chute cap into water port.
„ Insert vacuum hose or dust bag to fit into dust chute opening.
NOTE: A 1-1/4 in. vacuum hose will fit inside the dust chute,
a 1-7/8 in. vacuum hose will fit over the dust chute.
ATTACHING SAW TO A WATER HOSE
See Figure 5, page 14.
The water hose connection kit can be attached to the saw
to provide a continuous water supply. A pressure regulator
on the connection kit ensures the water pressure delivered
to the nozzle is equivalent to the water pressure of the bottle
connection.
NOTE: Wet cutting provides better cut quality than dry cutting.
OPERATION
„ Remove the battery pack from the saw.
„ Turn the flow adjustment knob clockwise to the OFF
position.
„ Depress the release button to remove water bottle if
installed.
„ Unscrew the nozzle assembly from water bottle.
„ Screw the nozzle assembly onto water hose connector.
„ Insert the nozzle assembly into saw as shown. Gently
press down on the water hose connector until it clicks
into place.
„ With the faucet turned completely off, attach the faucet
adaptor to a garden hose or outdoor faucet.
„ To remove water hose connector, depress the release
button.
NOTE: Keep the flow adjustment knob in the OFF position
until you are ready to begin wet cutting.
FLOW ADJUSTMENT KNOB
See Figure 6, page 14.
The flow adjustment knob can be used to adjust the rate of
water flow to the saw from the water bottle or water hose
connection kit.
To increase water flow:
„ Turn the flow adjustment knob counterclockwise.
To decrease water flow:
„ Turn the flow adjustment knob clockwise.
To stop water flow:
„ Turn the flow adjustment knob clockwise to the OFF
position.
LED WORKLIGHT
See Figure 6, page 14.
The LED worklight located on the front of the tool illuminates
when the switch trigger is depressed. If the tool is not in use,
the time-out feature will cause the light to shut off. The LED
worklight illuminates only when there is a charged battery
pack in the tool.
CUTTING WHEELS
The best of cutting wheels will not cut efficiently if they are
dull or badly worn. Using a dull wheel will place a heavy
load on the saw. Keep extra wheels on hand, so that sharp
wheels are always available.
WARNING:
Since wheel is exposed on underside of work, keep hands
and fingers away from cutting area. Any part of your
body coming in contact with moving wheel can result in
serious injury.
9 — English