Scheppach HS100S Traduccion Del Manual De Instrucciones Originale página 38

11. After fitting, check that the saw blade guard (4) is
functioning properly. Lift the saw blade guard and
then release it. The saw blade guard should auto-
matically move back to its starting position.
9. Using the saw
9.1 On/Off switch (fig. 14)
- The saw can be switched on by pressing the green
pushbutton „I". (11)
- The red pushbutton „0" (11) has to be pressed to
switch off the saw.
9.2 Cutting depth (fig. 14)
Turn the round handle (12) to set the blade (3) to the
required cutting depth.
- Anticlockwise: smaller cutting depth
- Clockwise: larger cutting depth
After each new adjustment it is advisable to carry out a
trial cut in order to check the set dimensions.
9.3 Setting the angle (fig. 14)
With the table saw you can make diagonal cuts to the
left oriented to the stop bar from 0 ° to 45 °.
m Check before each cut, that between the stop bar
(27), cross-stop (7) and the saw blade (3) a collision
is not possible.
- Undo the fixing handle (13).
- Set the desired angle on the scale by pressing and
turning the hand wheel (12).
- Lock the fixing handle (13) again in the required an-
gle position.
9.4 Working with the rip fence
9.4.1 Setting the stop height (figs. 15 - 16)
- The stop rail (27) of the rip fence (15) has two guide
surfaces with different heights.
- Depending on the thickness of the material to be cut,
the stop rail (27) as shown in fig. 16 must be used for
thick material (about 25 mm workpiece thickness)
and that shown in fig. 15 for thin material (less than
25 mm workpiece thickness).
38 | GB
9.4.2 Turning the stop rail (figs. 15 - 16)
- Loosen the wing nuts (28) first for rotating the stop
rail (27).
- Now, the stop rail (27) can be removed from the
guide rail (29) and pushed over it again using the
corresponding guide.
- Tighten the wing nuts (28) again.
- The stop rail (27) can be applied to the left or right of
the guide rail (29) as needed. To this end, only install
the bolts from the other side of the guide rail (29).
9.4.3 Setting the cutting width (fig. 17)
- The rip fence (15) must be used for longitudinal cut-
ting of wood parts.
- The rip fence (15) should be mounted on the right
side of the saw blade (3).
- Set the rip fence (15) on top of the guide rail for rip
fence (14).
- On the guide rail for rip fence (14), there are 2 scales
which indicate the distance between the rip fence
(15) and the saw blade (3).
- Select the appropriate scale depending on whether
the stop rail (27) is rotated for processing thick or
thin material:
High stop rail (thick material):
Low stop rail (thin material):
- Set the rip fence (15) to the desired level in the sight
glass and fix it with the eccentric lever for the rip
fence (30).
- When mounting or adjusting the rip fence, ensure
that the rip fence is aligned parallel to the saw blade.
9.5 Transverse stop (fig. 18)
- Push the transverse stop (7) into a groove (31a/31b)
of the saw bench.
- Loosen the handle screw (32).
- Turn the cross stop (7) until the desired angle is set.
The arrow on the transverse stop is at the set angle.
(0°-60°)
- Tighten the knurled screw (32) again.
- The stop rail (34) can be moved on the transverse
stop (7). Loosen the nuts (33) and push the stop rail
(34) to the desired position. Tighten the nuts (34)
again.
Caution!
- Do not push the stop rail (34) too far towards the
saw blade.
- The distance between the stop rail (34) and saw
blade (3) should be about 2 cm.
www.scheppach.com