Publicidad
Idiomas disponibles
Idiomas disponibles
Fax +32 030 9904733
ASSEMBLING THE HEATER AND CONNECTING THE GAS CYLINDER
1) After removing the heater from its packaging, check it for damage: if you are unsure, do not use the
appliance and contact qualified service personnel. The packing materials should not be left within
the reach of children because they are potentially dangerous; dispose of them in conformity with
the law.
2) Remove from the cabinet the cover on the gas cylinder, and unscrew.
3) This device must only be powered with LPG gas in a 15-kg cylinder and this must be equipped
with a pressure regulator and flexible tube. The pressure regulator must have a fixed calibration of
30 mbar conforming to EN12864 and the flexible rubber tube must be marked UNI-CIG 7140, with
a length of 50 cm (and not longer than 60 cm); the latter must be attached with metal bands of
suitable size and needs to be replaced by the date stamped on it (fig.2-3).
4) The heater must be provided with a regulator and hose: make sure they are included in the supply.
The flexible hose must be checked regularly whenever the cylinder is replaced to be sure it has no
scratches or cuts and it is in a perfect state. It must be replaced in any case before the expiry date
stamped on the hose itself.
5) Connect the flexible tube to the hose union of the pressure regulator and to that of the tap, checking
that the metal bands are tight and paying particular attention not to tamper with or damage any
component or fitting.
6) Before connecting the cylinder, make sure that its tap is closed and that there are no open flames
(lit oven, etc.) in the room, where the stove is placed. Screw the pressure regulator onto the
cylinder, keeping these warnings in mind:
A) check that the gasket seal is in good condition
B) attach the regulator to the tap, screwing the nut tightly counterclockwise.
C) carefully check that there is no gas leaking from the connection, using soapy water: if there
is a leak, bubbles will form; tighten the connection more or seek professionally qualified
service.
Warning: do not check for gas leaks when the appliance is hot, but wait until it is cold.
7)
Place the cylinder in its compartment, taking care that the tube is not twisted or choked and isn't
touching hot parts.
8)
Hook the rear cylinder cover on the cabinet, fix it with the screws supplied.
9)
The appliance has to be installed with the cover of the gas cylinder fixed to the cabinet. Use the
stove only woth a 15kg cylinder placed in its compartment.
10) To replace the cylinder, make sure that its tap is closed and that there are no open flames (lit
oven, etc.) or sources of heat in the place where you are working; we recommend that you
check that the gasket seals of the regulator and flexible rubber tube are in good condition and
replace them, if necessary.
11) To not mishandle the connections or other components.
12) Do not turn the cylinder upside down to completely use its contents: this releases liquid residues
left in the tank that will irreparably damage the heater.
13) Do not disconnect the pressure regulator from the cylinder when the cylinder tap is open.
14) The manufacturer will not be responsible if one of the above points is disregarded.
INSTALLATION
1)Use the stove only in well-aired rooms. In the room where the stove is placed there must be as
much air as it is necessary for the combustion. The room must have two breaches of 110cm² for the
air change.
2)The heater must be installed on a flat, stable surface.
3) Do not install or use the heater:
- in bathrooms;
- in bedrooms;
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar
(Italy). The pages must be reproduced and folded in
order to obtain a booklet A5 (+/- 148.5 mm width x 210
mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't
change the page numbering. Keep the language
integrity.
10
32
/
Assembly page 10/32
Publicidad
