Chicco Cuddle&Bubble comfort Manual página 12

USING THE CHANGING TABLE
Assembly
• The boxed product is already partially assem-
bled and the following instructions must be
performed to complete it:
1. Place frame A still packaged onto the oor
horizontally ( g. 1).
2. Install the 4 feet A3 and A4 ( g. 2).
All feet can be adjusted at 3 heights.
WARNING: To ensure the stability of the prod-
uct, make sure all the feet are mounted at the
same height, checking for proper engagement
of the pins into the holes on the legs ( g. 3).
WARNING: the two feet with the wheels A4 must
be installed on the same side of the product.
3. At this point, position the frame A upright,
grasp the two upper tubes and push them in
the opposite direction to open the product
(Fig. 4).
4. Pry down on both the intersections A5 until
you hear the engagement click ( g. 5).
5. Push the shelf A1 downwards by placing your
hand over the centre handle until fully engag-
ing it on the frame cross tube ( g. 6).
6. Install the storage basket C1 at the centre of
the front upper tubular frame, lining up the
two pins of basket C1 with the holes in the
tubular ( g. 7).
7. At this point hang the head wash C2 to the
right of the storage basket C1, by sliding it ver-
tically downwards into the guide ( g. 8).
8. Hook the sponge basket C3 to the left of the
storage basket C1 by sliding it vertically down-
wards into the guide ( g. 9).
9. Install the tub B onto the frame A, aligning the
side slots on the tub with the xing blocks ( g.
10-12). Complete the assembly of the tub by
inserting the rubber plug B1 in the relevant
slot and pressing the base of the plug ( g.11)
while rotating it in the relevant hole ( g. 11A).
10. Complete assembly by lifting the changing
table A2 and turning it to position it onto the
tub B ( g. 13).
WARNING: to prevent inadvertent rotation of the
changing table A2, make sure that the securing
straps A7 correctly engage clamps A6 through the
release buttons until you hear a click ( g. 13A - 13B).
Using the reducers
To ensure maximum comfort and ergonomics of
the changing table for use in the rst months of
a child's life, use the reducer in padded fabric C4
supplied (Fig. 16).
The reducer C4 can be removed or secured to
changing table A2 through the holes and velcro
found on product ( g. 14-15).
WARNING BATH TUB
IMPORTANT! READ CAREFULLY
AND KEEP FOR FUTURE REFER-
ENCE.
WARNING: BEFORE USE, REMOVE
AND DISPOSE OF ALL PLASTIC
BAGS AND PACKAGING MATERIALS
AND KEEP THEM OUT OF REACH OF
CHILDREN.
• WARNING - DROWNING HAZARD.
• WARNING:
drowned while bathing.
• WARNING: Children can drown
in as little as 2 cm of water in a
very short time.
• WARNING: Always remain in con-
tact with your child during bath-
ing.
• WARNING: Never leave your baby
unattended in the bath, even for a
few moments. If you need to leave
the room, take the baby with you.
• WARNING: This product shall not
be used on antiskid surfaces.
• Age of use allowed: From birth up
to 12 months and 11 kg. For do-
mestic use only.
• Babies and young children are
at risk of drowning when being
bathed.
• Never use this product on an el-
evated surface not intended for
this product (for example a table
or edges of the adult bath tub).
• When use in con guration not
stand alone: Use ONLY with the
changing unit frame sold togeth-
er with this product.
• To prevent burns from hot water,
place the product in such a way as
12
Children have