Lavorwash DOZZY 20 XS Instrucciones De Montaje página 14

• If an extension cord is used, the plug and socket must
be of watertight construction.
Before vacuuming liquids, check the float functions
•
correctly. When vacuuming liquids, and when the
tank is full, a float closes the suction opening, and the
vacuum operation is interrupted. Then switch off the
machine, disconnect the plug and empty the tank.
Regularly clean the water level limiting device (float)
and examine it for signs of damages.
• If the machine overturns, it would be recommended
to stand it up before switching off.
If foam or liquid escape from the appliance, switch off
•
immediately..
The equipment should not be used to vacuum wa-
•
ter from containers lavatories, tubs, etc.
Aggressive solvents or detergents should not be
•
used.
Service and repairs must be carried out by qualified
•
personnel only. Only use manufacturer original spare
parts for service repair.
The manufacturer cannot be held responsible for any
•
damage/injury caused to persons, animals or proper-
ty caused by misuse of the appliance,
USE
• Be sure that switch is in off position (0) OFF and con-
nect the machine to a suitable socket.
• The machine must be always kept on horizontal ba-
ses, in a safe and stable way.
• Insert the suitable filters for the proper use.
Never use the appliance without filters .
•
• Use the most suitable accessories for the requested
usage.
• Put switch on (-) ON position in order to start the ma-
chine.
• When job is over, switch off (0) OFF and keep away the
plug from the socket.
• If the appliance is used with especially fine dust (size
below 0.3 µm) the filter supplied will require cleaning
more frequently. For especially demanding applica-
tions, the use of specific filters supplied as an optional
(Hepa) may be necessary.
DUST SUCTION
Only work with dry cartridge filter!
Tip: For fine dust extraction insert filter bag.
NOTES ON THE FILTER BAG
(see fig. ④)
• The level of filling of the filter bag depends on the dirt
that is being sucked in.
14
• In the case of fine dust, sand, etc., change the filter
bag frequently.
OUTLET MODELS
see fig. (⑨)
To activate the socket-electric tool function, put
switch (D) on (|)ON and switch (D1) on (0) OFF. When
a tool is connected the vacuum will automatically
start as the tool is started. The suction hose will
suck directly dust and wood shavings.
• Even when switches (D) and (D1) are (|) ON , the
electric tool socket is live. Not suitable for any hot
items.
If the electric tool is switched off, the suction turbine
continues to run for approx. 8 seconds in order to va-
cuum up the remaining dirt in the suction hose.
FILTER CLEANING
(see fig. ⑧)
The machine shall be disconnected from its power
•
source, by removing the plug from the socket-outlet,
during cleaning or maintenance
1- Remove the filter N,Z
2- Shake the filter N,Z
3- wash tge filter N,Z
4- Let the filter N,Z drying very well ,befor reassemble it
Once the filter has been cleaned, check whether it
•
is suitable for further use. If it has been damaged or
broken, replace it with an original filter.
CARE AND MAINTENANCE
The unit is maintenance-free.
The machine shall be disconnected from its pow-
•
er source, by removing the plug from the sock-
et-outlet, during cleaning or maintenance
• Clean the exterior part of the machine with a dry cloth.
• Move the appliance only by catching the carrying
handle located on the motor head.
• Store the appliance and the accessories in a dry
safe place, out of the reach of children.
AUTOMATIC FILTER SHAKER C
(see fig. ⑧)
If there should be a reduction in the suction power,
operate the filter shaker a few times.
WARRANTY CONDITIONS
All our machines are subjected to strict tests and are cov-
ered against manufacturing defects in accordance with
applicable regulations. The warranty is effective from