Publicidad
Listening to Bluetooth enabled devices (continued)
5
"Connected" appears on the display once the unit is
successfully paired with the source device. (Pairing
information is now memorised in the unit.) Some au-
dio source devices may connect with the unit automa-
tically after pairing is completed, otherwise follow the
instructions in the source device operating manual to
start connection.
6
Press the play button on main unit, remote control or
source device to start Bluetooth streaming playback.
Notes:
If a device such as microwave oven, wireless LAN card, Blue-
●
tooth device or any other device that uses the same 2.4 GHz
frequency is placed near the system some sound interruption
may be heard.
The transmission distance of the wireless signal between the de-
●
vice and the main unit is about 10 m, but may vary depending on
your operating environment.
If a steel concrete or metallic wall is between the device and the
●
main unit, the system may not operate at all, because the wire-
less signal cannot penetrate metal.
If this unit or the source device is turned off before Bluetooth con-
●
nection is completed, pairing will not be completed and the pair-
ing information will not be memorised. Repeat step 1 onward to
start pairing again.
To pair with other devices, repeat steps 1 - 5 for each device. This
●
unit can memorise up to a maximum of 99 devices. If subsequent
device is paired, the oldest device paired will be deleted.
Once a device is ousted or deleted from the pairing list, the pair-
●
ing information for the device is also deleted. To listen to the
sound from the device again, it needs to be re-paired. Perform
steps 1 - 5 to pair the device again.
XL-LS703BH supports Bluetooth profile AVRCP 1.4. If your de-
●
vice supports the same profile (refer to device manufacturer's
specification), XL-LS703BH is able to control the volume of the
device and display the song information (title, album, artist).
Note:
Some music applications do not support this feature, hence there
will be no volume synchronisation and no song information will be
displayed even if your Bluetooth device supports such profile.
■ Listening to the sound
Check that:
The source device Bluetooth functionality is ON.
●
Pairing of this unit and the source device is completed.
●
Unit is in connected mode.
●
1
Press the ON/STANDBY button to turn the power on.
2
Press the FUNCTION button (main unit) repeatedly to
select Bluetooth function.
3
Start the Bluetooth connection from the Bluetooth au-
dio source device.
4
Press the BLUETOOTH / button.
Notes:
For various Bluetooth operations, refer "NFC connection
●
for audio playback" on page 7.
If the source device has an extra bass function or equalizer
●
function, set them to off to avoid sound distortion.
Note:
Make the Bluetooth connection again if the source device is not
●
turned on, or its Bluetooth functionality is off or is in sleep mode.
The volume of this unit may not be controlled as intended de-
●
pending on the device.
■ To disconnect the Bluetooth device
Perform any of the followings.
– Press PAIRING button until "Disconnected" appears on the
display.
– Disconnect or turn off the Bluetooth connection on the audio
source device. Refer the operating manual supplied with the
device.
– Turn off this unit.
■ Auto power on
During Bluetooth standby mode, the unit will automatically
power on when the Bluetooth connection is set up between
the main unit and your device.
Note:
This function is not applicable during Bluetooth standby
mode off.
Listening on Android™ devices
■ Introduction : Open Accessory
Open Accessory support allows external USB hardware
(an Android USB accessory) to interact with an Android-
powered device in a special accessory mode. When an
Android-powered device is in accessory mode, the con-
nected accessory acts as the USB host (powers the bus
and enumerates devices) and the Android-powered device
acts in the USB accessory role. Android USB accessories
are specifically designed to attach to Android-powered
devices and adhere to the Open Accessory Protocol, that
allows them to detect Android-powered devices that support
accessory mode.
■ Android device connection (USB)
1
Insert the connector to the device.
Device
(Smartphone/Tablet)
Connector
2
Connect the device to the main unit via USB connector.
■ Android device playback
1
Press the ON/STANDBY button to turn the power on.
2
Press the FUNCTION button repeatedly (main unit) to
select USB function.
3
Connect the device (Smartphone/Tablet) to the unit.
"USB Media" will be displayed.
4
Press the play button (on main unit, remote control or device).
Notes:
● If the source device has an extra bass or equalizer
function, set them to off. If these functions are on,
sound may be distorted.
● Incoming calls will pause the playback/application.
● Once the calls are answered, the conversation can
only be heard through the built-in speaker of the cel-
lular device. Turn on the device speaker or disconnect
the device to start conversation.
E-8
USB connector
(not supplied)
Publicidad
