SunPower SPR X Serie Instrucciones De Seguridad E Instalación página 12

SunPower Maxeon 3 128 cells Solar Panel
(SPR-Xyy-XXX-COM)
0
150
311
E
Measurement Tolerances are +/-3 mm for the Length and Width of the Module.
TOP CLAMPS
Moun ng Moun ng Configura on Diagram
Configura on
Descrip on Front View Back View
Long Side Moun ng,
Rails Perpendincular
to Moun ng Frame
Long Side Moun ng,
Point Supported
Long Side Moun ng,
Rails Parallel to
Moun ng Frame
Short Side Moun ng,
Rails Perpendicular to
Moun ng Frame
(End Mount)
Short Side Moun ng,
Point Supported
(End Mount)
Short Side Moun ng,
Rails Parallel to
Moun ng Frame
(End Mount)
1 In the cases where hybrid moun ng is necessary (combina on of long and short side moun ng), the lowest
design load values should be considered as allowable design load.
2 Test loads are for informa on purposes only, design loads should be considered for the project design.
3 Design Load considers 1.5 Factor of Safety, Test load = Design load x 1.5. Product Warranty covers only design
load values. The design loads listed in this table supersede all other loads that may be defined by other
par es, unless there is a formal authoriza on by Maxeon.
©June 2023 Maxeon Solar Technologies, Ltd. All rights reserved. Specifications included in this manual are subject to change without notice.
554 885
C
D
300 mm
400 mm
539 mm
1058 mm
1200 mm
1423 mm
2047 mm
Moun ng Zone
Test Load Design Load
Loca ons
Downward/Upward
(distance from corner Downward/Upward
(Pa)
(Pa)
in mm)
0 - 150 +2000/-2000 +1333/-1333
150 - 311 +5400/-3600 +3600/-2400
311 - 554 +5400/-3600 +3600/-2400
554 - 885 +5400/-3600 +3600/-2400
0 - 150 +2000/-2000 +1333/-1333
150 - 311
+3600/-3600 +2400/-2400
311 - 554 +5400/-3600 +3600/-2400
554 - 885 +3600/-3600 +2400/-2400
0 - 150 +1333/-1333
+2000/-2000
150 - 311 +2400/-2400
+3600/-3600
311 - 554 +3600/-2400
+5400/-3600
554 - 885
+3600/-3600 +2400/-2400
0 - 350
+2400/-2400 +1600/-1600
+2000/-2000
0 - 350 +1333/-1333
+1600/-1600
0 - 350 +2400/-2400
Safety and Installation Instructions - Document 001-15497 Rev.AA
885 554
A - Drainage Holes (4X Ø4.8mm)
B - Stacking Pins (4X Ø6.10mm)
C - Moun ng Holes (24X Ø6.8mm)
D - Slots (4X 5.0mm(W) x 15.0mm(L))
E - Ground Holes (4X Ø4.2mm)
GEN 4.0 FRAME PROFILE
SIDE FRAME PROFILE
10.30 mm
3.18 mm
46.08 mm
18.50 mm
2.20 mm
32 mm
BOLTS
Moun ng
Moun ng Configura on Diagram
Configura on
Descrip on
Front View Back View
Long Side Moun ng,
Rails Perpendincular
to Moun ng Frame
Long Side Moun ng,
Point Supported
4 Rails must not be under the junc on box.
6 Bo om flange moun ng.
7 Range indicates posi oning of the clamp and not the rails.
MAXEON SOLAR TECHNOLOGIES, LTD.
0
150
311
B A
398 mm
END FRAME PROFILE
10.50 mm
46.08 mm
1.27 mm
22 mm
Moun ng Zone
Test Load Design Load
Loca ons
(distance from corner
Downward/Upward Downward/Upward
(Pa) (Pa)
in mm)
1423mm Holes +5400/-3600
+3600/-2400
1200mm Holes +5400/-3600 +3600/-2400
539mm Holes +3600/-3600 +2400/-2400
400mm Holes +3600/-3600 +2400/-2400
300mm Holes +3600/-3600 +2400/-2400
1423mm Holes +5400/-3600 +3600/-2400
+5400/-3600 +3600/-2400
1200mm Holes
539mm Holes
+3600/-3600 +2400/-2400
400mm Holes +3600/-3600 +2400/-2400
300mm Holes
+3600/-3600 +2400/-2400