SunPower SPR X Serie Instrucciones De Seguridad E Instalación página 9

SunPower Maxeon 3 104 cells Residen al Solar Panel
(SPR-MAX3-XXX, SPR-MAX3-XXX-BLK)
0
150
50 254
TOP CLAMPS
Moun ng
Moun ng Configura on Diagram
Configura on
Descrip on
Front View Back View
Long Side Moun ng,
Rails Perpendincular
to Moun ng Frame
Long Side Moun ng,
Point Supported
Long Side Moun ng,
Rails Parallel to
Moun ng Frame
Short Side Moun ng,
Rails Perpendicular to
Moun ng Frame
(End Mount)
Short Side Moun ng,
Point Supported
(End Mount)
Short Side Moun ng,
Rails Parallel to
Moun ng Frame
(End Mount)
1 In the cases where hybrid moun ng is necessary (combina on of long and short side moun ng), the lowest
design load values should be considered as allowable design load.
2 Test loads are for informa on purposes only, design loads should be considered for the project design.
3 Design Load considers 1.5 Factor of Safety, Test load = Design load x 1.5. Product Warranty covers only design
load values. The design loads listed in this table supersede all other loads that may be defined by other
par es, unless there is a formal authoriza on by Maxeon.
©June 2023 Maxeon Solar Technologies, Ltd. All rights reserved. Specifications included in this manual are subject to change without notice.
423
646
1100 mm
1300 mm
1500 mm
1690 mm
Measurement Tolerances are +/-3 mm for the Length and Width of the Module.
A - Ground Holes (4X Ø4.2mm)
B - Moun ng Holes (8X Ø6.8mm)
Moun ng Zone
Test Load Design Load
Loca ons
Downward/Upward Downward/Upward
(distance from corner
(Pa) (Pa)
in mm)
50 - 150 +2700/-2700 +1800/-1800
150 - 254 +2400/-2400
+3600/-3600
+5400/-5400 +3600/-3600
254 - 423
+3600/-3600
423 - 646 +2400/-2400
50 - 150 +1800/-1800
+2700/-2700
150 - 254 +2400/-2400
+3600/-3600
+5400/-5400
254 - 423 +3600/-3600
423 - 646 +3600/-3600 +2400/-2400
50 - 150 +1800/-1800
+2700/-2700
150 - 254 +2400/-2400
+3600/-3600
254 - 423 +3600/-3600
+5400/-5400
423 - 646
+3600/-3600 +2400/-2400
0 - 350 +1800/-1800
+2700/-2700
+2700/-2700 +1800/-1800
0 - 350
0 - 350 +2700/-2700 +1800/-1800
Safety and Installation Instructions - Document 001-15497 Rev.AA
423
646
GEN 4.2 FRAME PROFILE
SIDE FRAME PROFILE
32 mm
BOLTS
Moun ng
Moun ng Configura on Diagram
Configura on
Descrip on
Front View Back View
Long Side Moun ng,
Rails Perpendincular
to Moun ng Frame
Long Side Moun ng,
Point Supported
4 Rails must not be under the junc on box.
6 Bo om Flange Moun ng.
7 Range indicates posi oning of the clamp and not the rails.
MAXEON SOLAR TECHNOLOGIES, LTD.
0
150 50
254
B
A
END FRAME PROFILE
24 mm
Moun ng Zone
Test Load Design Load
Loca ons
Downward/Upward Downward/Upward
(distance from corner
(Pa) (Pa)
in mm)
1300mm Holes
+8100/-3600 +5400/-2400
1100mm Holes +8100/-3600
+5400/-2400
1300mm Holes +5400/-3600 +3600/-2400
400mm Holes +5400/-3600
+3600/-2400