Hotpoint Ariston FKQ 831 0 (BK)/HA Manual De Instrucciones página 18

Start-up and use
GB
! The first time you use your appliance, heat the empty oven with its door closed
at its maximum temperature for at least half an hour. Make sure that the room
is well ventilated before switching the oven off and opening the oven door. The
appliance may emit a slightly unpleasant odour caused by protective substances
used during the manufacturing process burning away.
Starting the oven
1. Select the desired cooking mode by turning the SELECTOR knob.
2. Select the desired temperature using the THERMOSTAT knob. A list
detailing cooking modes and suggested cooking temperatures can be found
in the Cooking advice table (see Cooking modes).
3. The THERMOSTAT indicator light indicates that the oven is heating up to
the temperature set.
4. During cooking it is always possible to:
- change the cooking mode by turning the SELECTOR knob;
- adjust the temperature by turning the THERMOSTAT knob;
- stop cooking by turning the SELECTOR knob to the "0" position.
! Never put objects directly on the bottom of the oven; this will prevent the
enamel coating from being damaged.
! Always place cookware on the rack(s) provided.
Cooling ventilation
In order to cool down the external temperature of the oven, a cooling fan
blows a stream of air between the control panel and the oven door, as well
as towards the bottom of the oven door.
! Once cooking has been completed, the cooling fan continues to operate
until the oven has cooled down sufficiently.
Oven light
When selecting with the SELECTOR knob the oven light goes on. It
remains lit when a cooking mode is selected.
18
WARNING! The oven is provided with
a stop system to extract the racks and
prevent them from coming out of the
oven (1).
As shown in the drawing, to extract
them completely, simply lift the racks,
holding them on the front part, and
pull (2).
The electronic programmer
END OF
COOKING icon
DURATION
icon
DECREASE TIME
button
Setting the clock
! The clock may be set when the oven is switched off or when it is switched
on, provided that a the end time of a cooking cycle has not been programmed
previously.
After the appliance has been connected to the mains, or after a blackout, the
icon and the four numerical digits on the DISPLAY will begin to flash.
1. Press the button several times until the
the display begin to flash.
2. Use the " " and " " buttons to adjust the time; if you press and hold either
button, the display will scroll through the values more quickly, making it quicker
and easier to set the desired value.
3. Wait for 10 seconds or press the
Setting the timer
! This function does not interrupt cooking and does not affect the oven; it is
simply used to activate the buzzer when the set amount of time has elapsed.
1. Press the button several times until the
on the display begin to flash.
2. Use the " " and " " buttons to set the desired time; if you press and hold
either button, the display will scroll through the values more quickly, making
it quicker and easier to set the value.
3. Wait for 10 seconds or press the
The display will then show the time as it counts down. When this period of
time has elapsed the buzzer will be activated.
Programming cooking
! A cooking mode must be selected before programming can take place.
Programming the cooking duration
1. Press the button several times until the
on the DISPLAY begin to flash.
2. Use the " " and " " buttons to set the desired duration; if you press and
hold either button, the display will scroll through the values more quickly,
making it quicker and easier to set the value.
3. Wait for 10 seconds or press the
4. When the set time has elapsed, the text END appears on the DISPLAY,
the oven will stop cooking and a buzzer sounds. Press any button to stop it.
• For example: it is 9:00 a.m. and a time of 1 hour and 15 minutes is
programmed. The programme will stop automatically at 10:15 a.m.
DISPLAY
CLOCK icon
TIMER icon
INCREASE TIME
button
SET TIME
button
icon and the four digits on
button again to finalise the setting.
icon and the three digits
button again to finalise the setting.
icon and the three digits
button again to finalise the setting.