Publicidad
Idiomas disponibles
Idiomas disponibles
Adjusting Depth (Fig. 10)
The depth that the fastener is driven can be adjusted using the depth adjustment wheel (C) on
the side of the tool.
WARNING: To reduce risk of serious injury from accidental actuation when
attempting to adjust depth, ALWAYS:
• Remove battery pack.
• Engage contact trip lock-off.
• Avoid contact with trigger during adjustments.
1. To drive the nail shallower, rotate the depth adjustment wheel (C) counterclockwise. There
are six depth settings, 1 being the shallowest and 6 being the deepest.
2. To sink a nail deeper, rotate the depth adjustment wheel (C) clockwise.
FIG. 10
D
C
Headlights (Fig. 10)
There is a headlight (D) located on each side of the nailer. Headlights turn on upon battery
insertion, activation of the trigger, or depressing the contact trip. The lights will automatically
shut off after 10 seconds unless tool remains in use.
NOTE: These headlights are for lighting the immediate work surface and are not intended to
be used as flashlights.
LOW BATTERY INDICATOR: The headlights will flash four consecutive times and then shut
down to indicate low battery.
JAMMED NAIL INDICATOR: The headlights will flash continually if a nail becomes jammed
in the nosepiece (see Clearing a Jammed Nail).
Clearing a Jammed Nail (Fig. 11)
If a nail becomes jammed in the nosepiece, keep the tool pointed
away from you and follow these instructions to clear:
1. Remove battery pack from tool and engage contact trip lock-off.
2. Pull the pusher back until it locks in place then remove the nails.
3. Lift the jam clearing latch (E) then pull up to open front door (O).
4. Remove bent nail, using pliers if necessary.
5. If driver blade is in the down position, insert screwdriver or other
rod into nosepiece and push driver blade back in position.
6. Close the front door and engage the wireform under the 2 arms
(N) on the nosepiece. Push latch until it locks in place.
7. Reinsert battery pack.
NOTE: The tool will disable itself and not reset until the battery pack has been removed
and reinserted.
8. Reinsert nails into magazine (see Loading the Tool).
9. Release pusher.
NOTE: Should nails continue to jam frequently in nosepiece, have tool serviced by an
authorized D
WALT service center.
E
Cold Weather Operation
When operating tools at temperatures below freezing:
1. Keep tool as warm as possible prior to use.
2. Actuate the tool 5 or 6 times into scrap lumber before using.
Hot Weather Operation
Tool should operate normally. However, keep tool out of direct sunlight as excessive heat can
deteriorate bumpers and other rubber parts resulting in increased maintenance.
Suspension Hook (Fig. 12)
The D
WALT cordless nailers include an integrated suspension hook (J)
E
and can be attached to either side of the tool to accommodate left- or
right-handed users.
If the hook is not desired at all, it can be removed from the tool.
TO REMOVE SUSPENSION HOOK
1. Remove battery pack from tool.
2. To switch the tool from right- to left-hand usage simply remove the
screw from the opposite side of the tool and reassemble on the
other side.
3. Replace battery pack.
WARNING: Remove nails from magazine before making any adjustments or servicing this
tool. Failure to do so may result in serious injury.
CAUTION: Disconnect battery pack from tool before making any adjustments,
changing accessories, servicing, or moving the tool. Such preventative safety measures
reduce the risk of starting the tool accidentally.
CAUTION: When not in use, place tool on its side on a stable surface where it will
not cause a tripping or falling hazard. Some tools with large battery packs will stand
upright on the battery pack but may be easily knocked over.
MAINTENANCE
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
ACTION Clean magazine, pusher, and contact trip mechanism.
WHY
Permits smooth operation of magazine, reduces wear, and prevents jams.
FIG. 11
HOW
Blow clean with compressor air. The use of oils, lubricants periodically or solvents is not
recommended as they tend to attract debris.
ACTION Before each use, check to insure all screws, nuts and fasteners are tight and undamaged.
WHY
Prevents jams and premature failure of tool parts.
HOW
Tighten loose screws or other fasteners using the appropriate allen wrench or screwdriver.
N
Cleaning
E
O
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this.
9
Daily Maintenance Chart
FIG. 12
J
Publicidad
