Publicidad
RESOLUCIÓN DE PROBLEMAS
PROBLEMA
POSIBLE CAUSA Y SOLUCIÓN
El artefacto no se enciende.
El artefacto no está enchufado. Enchufe el cable de alimentación en la toma de corriente eléctrica.
Asegúrese de que el artefacto se encuentra en modo de ventilador.
Se quemó el fusible. Reemplace el fusible (Vea INSTRUCCIONES DE FUNCIONAMIENTO DEL
USUARIO).
La unidad está dañada o necesita reparación. Suspenda el uso y desenchúfela. Comuníquese con el
servicio de atención al cliente para obtener asistencia.
El enchufe está gastado o dañado. Pruebe con otro enchufe o contacte a un electricista certifi cado.
El fl ujo de aire es débil o
Confi gure la unidad a una velocidad baja. Ajústela a una confi guración de velocidad más alta.
lento.
El fl ujo de aire está bloqueado. Quite la obstrucción.
Ajuste la dirección de la corriente de aire hacia el usuario.
El GFCI se detiene.
Bajo ciertas condiciones, es posible que un enchufe GFCI recolocado no funcione cuando el usuario
cambia la velocidad del circulador Vornado. En este caso, cambie a un enchufe que no esté conectado
a un artefacto GFCI. Asimismo, esto podría indicar que el enchufe GFCI se encuentra en mal estado o
defectuoso. Comuníquese con un electricista certifi cado para que verifi que el enchufe GFCI.
20 Español
Contact Vornado Consumer Service at 1-800-234-0604 (phone) or
consumerservice@vornado.com (email) for further instructions about
replacement and repair.
- Before plugging power cord into electrical outlet, be sure that
all electrical information on the rating label, including voltage, is
compatible with your outlet's power supply.
- Do not sit or stand on product.
- Never use the cord as a handle or otherwise yank, strain or stretch
the power cord.
- While the product is plugged in, do not insert or allow foreign
objects to enter any input or output opening as this may cause risk
of electric shock or fi re, or damage the product.
- A loose fi t between wall outlet (receptacle) and plug may cause
overheating and distortion of the plug. Discontinue use of the
product in this outlet. Contact a qualifi ed electrician to replace
loose or worn outlets.
- This appliance has a polarized plug (one blade is wider than the
other.) To reduce the risk of electric shock, this plug is intended to
fi t in a polarized outlet only one way. If the plug does not fi t fully in
the outlet, reverse the plug. If it still does not fi t, contact a qualifi ed
electrician. Do not attempt to defeat this safety feature.
- Before moving, repositioning, servicing, cleaning and when not in
use, use the product controls to turn off the power and then unplug.
To disconnect from outlet, grasp and pull only the plug. Also, power
off and unplug if the product will be left unattended for an extended
period of time or during electrical storms.
SERVICING WARNING—To reduce risk of fi re, electrical shock
and injury to persons, observe the following:
- Clean your product regularly, only as is instructed in this manual.
Prior to cleaning, turn off the power on your product and unplug. Do
not use gasoline, thinners, solvents, ammonias or other chemicals
for cleaning. Refer to the CLEANING instructions provided.
- Do not open appliance housing while product is plugged in. To
avoid risk of shock, all service and/or repairs must be done by a
Vornado Authorized Service Center.
- This product employs overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation. If the fuse blows,
unplug the product from the outlet. Replace the fuse as per the user
servicing instructions (follow product marking for proper fuse rating)
and check the product. If the replacement fuse blows, a short-circuit
may be present and the product should be discarded or returned to
an authorized service facility for examination and/or repair.
User Servicing Instructions
1. Using the product controls, turn off the appliance.
2. Grasp the plug (not the cord) and disconnect from the outlet.
3. Risk of Fire. Replace fuse only with 2.5 Amp, 125 Volt fuse as
approved by Vornado Consumer Service. For an authorized
replacement fuse, please contact Vornado Consumer Service.
4. Once the replacement is received, use a small fl at-head
screwdriver to slide open the fuse cover (located on the plug)
(See next page, Fig. A).
5. Remove fuse by using the screwdriver to gently lift each end of
the fuse (See next page, Fig. B).
6. Install the replacement fuse by using the screwdriver to gently
push each metal end of the fuse into the receptacle one at a
time. Do not push on the center of the fuse—it is fragile and
may break.
7. Slide the fuse cover closed using the screwdriver. When
closed, the cover should fi t completely in the plug. No part of
the cover should stick out (See next page, Fig. C).
English
5
Publicidad
