Descargar Imprimir esta página

Bosch 06019B2900 Manual Original página 13

Publicidad

OBJ_BUCH-1417-001.book Page 12 Tuesday, May 17, 2011 11:37 AM
12 | English
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
2
a
<2.5 m/s
, K=1.5 m/s
.
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Technical Data
Cordless Universal Cutter
Article number
Rated voltage
No-load speed
Cutting capacity/charged
battery (4 mm PVC), approx.
Weight according to
EPTA-Procedure 01/2003
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2004/108/EC,
2006/42/EC.
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Dr. Eckerhard Strötgen
Senior Vice President
Head of Product
Engineering
Certification
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 18.05.2011
1 609 929 Y38 | (17.5.11)
Assembly
Battery Charging
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
9 indicate the charge condition of the battery 6. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
– To indicate the charge condition, press and hold button 8
GUS 10,8 V-LI
Professional
LED
3 603 JB2 9..
Continuous lighting 3 x green
V=
10.8
Continuous lighting 2 x green
-1
min
700
Continuous lighting 1 x green
Flashing light 1 x green
m
200
Removing the Battery (see figure A)
– To remove the battery 6, press the unlocking buttons 7 and
kg
1.0
Changing the Tool (see figures B1
– Loosen knurled screw 1 and set blade guard 3 to the upper
– Rotate the blade 10 with a screwdriver until one of the
– Insert a thin, sturdy object (e.g., a nail) into the free hole,
– Unscrew the blade screw 11.
– Remove the object with which you blocked the blade.
– Slightly lift off the blade and pull it out towards the bottom.
– Attach the new blade onto the tool holder ensuring that the
– Tighten the blade screw again.
– Adjust blade guard 3 to the material thickness to be cut
Use only the battery chargers listed on the graphics
page. Only these battery chargers are matched to the lith-
ium ion battery used in your machine.
of the switched off machine.
pull the battery out of the machine to the rear. Do not ex-
ert any force.
The blade can become warm during operation. Before
removing, allow the blade to cool down.
position.
holes in the blade is free (uncovered).
to block the blade.
ground edge of the blade faces you.
Pay attention that the blade engages onto the tool holder.
and tighten knurled screw 1 again.
Capacity
≥2/3
≥1/3
<1/3
Reserve
B2)
Bosch Power Tools

Publicidad

loading

Este manual también es adecuado para:

Gus 10,8 v-li professional06019b290406019b29013 603 jb2 9