Publicidad
Idiomas disponibles
Idiomas disponibles
PANEL FACILITIES
See page 2 for Panel Facilities.
[FRONT PANEL]
1) POWER
(STANDBY/ON) switch/indicator
*
With the power cord connected to a wall outlet, the unit
will always
be supplied
with
power
and remains
in
standby condition when it is turned off by pressing the
power switch.
¢ The indicator lights during standby.
®
The accessory remote control unit can also be used to
turn the amplifier on or standby (STANDBY function).
°
The POWER
switch selects the transformer secondary
even in STANDBY
position. The unit circuitry will work
as long as the power cord is connected to a wall socket.
¢ When not using the unit for a long period, disconnect the
power cord.
2) SP-A selector switch/indicator
Depress this switch for sound reproduction with the speaker
systems connected to the SPEAKERS A terminals.
ON:
The
indicator
lights: Sound
is heard
from the speaker
systems.
OFF:
The indicator is off: No sound is heard from the speaker
systems.
Set
to
this
position
when
listening
with
headphones.
3) SP-B selector switch/indicator
Depress this switch for sound reproduction with the speaker
systems connected to the SPEAKERS B terminals.
ON:
The
indicator lights: Sound
is heard
from
the speaker
systems.
OFF:
The indicator is off: No sound is heard from the speaker
systems.
Set
to
this
position
when
listening
with
headphones.
NOTE:
SP-A and SP-B cannot be used at the same time.
@ PHONES jack
When using headphones, insert the plug into this jack.
@ BASS EO switch/indicator
By pressing this switch (ON), the indicator will light and
powerful sound reproduction will be obtained.
Use this function as desired when listening to a digital source
such as a compact disc.
NOTE:
This function does not operate when the CD DIRECT or DAT DIRECT
switch is in the ON position.
@ BASS EQ LEVEL control
When the BASS EQ switch is ON, you can vary the degree
of enhancement
of very low frequencies
below
60 Hz
continuously,
using this control.
Set this control to the
desired position.
NOTE:
This control does not operate when the CD DIRECT or DAT DIRECT
switch is in the ON position.
(7) BASS tone control
Use to adjust the low-frequency tone. The center position
is the FLAT (normal) position. When moved to the right, low-
frequency tones are emphasized; when moved to the left,
low-frequency tones are de-emphasized.
NOTE:
This control does not operate when the CD DIRECT or DAT DIRECT
switch is in the ON position.
(3) TREBLE tone control
Use to adjust the high-frequency tone.
The center position is the FLAT
(normal) position. When
moved to the right, high-frequency tones are emphasized;
when
moved
to the left, high-frequency
tones
are de-
emphasized.
NOTE:
This control does not operate when the CD DIRECT or DAT DIRECT
switch is in the ON position.
© BALANCE control
Should normally be left in the center position. Adjust balance
if the sound is louder from one of the speakers. If the right
side is louder, move toward the LEFT and if the left side is
louder, move toward the RIGHT.
NOTE:
This control does not operate when the CD DIRECT or DAT DIRECT
switch is in the ON position.
@ REC SELECTOR switch/indicator
Switch to select the recording signal. When set to a position
other than SOURCE or OFF, signals of the corresponding
equipment can be recorded while listening to the equipment
selected by the input selector switches.
SOURCE:
To record from the equipment selected by the input selector
switches.
TUNER:
To record from the equipment connected to the TUNER
terminals.
DAT
>
TAPE:
To record (copy) from the tape deck connected to the DAT
terminals over to the tape deck connected
to the TAPE
terminals.
5
<ARE1080>
SETS
NP
SSS
TE
SE
EG
EEE
'
i
SR
RUS SS
ST
ON
EGRTE
f '
sigs
SO SIT
ESS
USES
SETS
SS
SS
SECT
STS
Tai
iaainici
ai auatuuaeaaa
RT
RT RETE
Publicidad
