Skil 9003 Instrucciones página 6

SAFETY INSTRUCTIONS FOR ANGLE GRINDERS
GENERAL
Only use this tool for dry grinding/cutting
Only use the flanges which are supplied with this tool
This tool should not be used by people under the age of
16 years
Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
Use the original SKIL accessories which can be
obtained from your SKIL dealer
For mounting/using non-SKIL accessories observe the
instructions of the manufacturer concerned
Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
Do not use damaged, deformed or vibrating grinding/
cutting discs
Handle and store grinding/cutting discs carefully to avoid
chipping and cracking
Protect accessories from impact, shock and grease
Do not use a grinding/cutting disc that is larger than the
maximum recommended size
Only use grinding/cutting discs with a hole diameter
which fits mounting flange D 6 without play; never use
reducors or adaptors to fit large-hole grinding/cutting
discs
Never use grinding/cutting discs with a threaded hole, of
which the thread is not long enough to accept the
spindle length of the tool
Never use accessories with a "blind" threaded hole
smaller than M14 x 21 mm
OUTDOOR USE
Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
Only use an extension cord which is intended for
outdour use and equipped with a splashproof coupling-
socket
BEFORE USE
Before using the tool for the first time, it is recommended
to receive practical information
Do not work with materials containing asbestos
Be careful of hidden electrical wires or gas- and water
pipes; check the work area, for instance with a metal
detector
Be careful when cutting grooves, especially in
supporting walls (slots in supporting walls are subject to
country-specific regulations; these regulations are to be
observed under all circumstances)
Clamp the workpiece in case it does not remain
stationary from its own weight
Do not clamp the tool in a vice
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (UK 13 Amps)
Wear protective glasses and gloves, hearing
protection 3, a dust mask, and sturdy shoes; when
necessary, also wear an apron
Always mount auxiliary handle A 6 and protective guard
B 6; never use the tool without them
Be sure tool is switched off when plugging in
DURING USE
Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug;
never use the tool with a damaged cord
Push spindle-lock button G 6 only when spindle C 6 is
at a standstill
Keep hands away from rotating accessories
When grinding metal, sparks are generated; keep other
persons and combustible material from work area
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
In case the cutting disc is blocked, resulting in jerking
forces on the tool, immediately switch off the tool
In case of current interruption or when the plug is
accidentally pulled out, unlock the on/off switch H 6
immediately and put it in the OFF-position in order to
prevent uncontrolled restarting
Do not apply so much pressure on the tool that it comes
to a standstill
AFTER USE
Before you put down the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left
unattended
USE
Mount auxiliary handle A 4
Mount protective guard B 5
! ensure that the closed side of the protective
guard always points to the operator
Mounting of accessories 6
! disconnect the plug
- clean spindle C and all parts to be mounted
- tighten clamping flange E with spanner F while
pushing spindle-lock button G
- for removing accessories handle vice-versa
! grinding/cutting discs become very hot during
use; do not touch them until they have cooled
down
! always mount backing pad when using sanding
accessories
! never use a grinding/cutting disc without the label
("blotter") which is glued onto it
Before using the tool
- ensure that accessory is correctly mounted and firmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
6