SIOUX 5564A Instrucciones Para El Operador

Form # Z369A
Date 2-02/A
Model 5564A
3" Cut Off Tool
Operator Instructions
Includes - Foreseen Use, Work Stations, Putting Into Service,
Operating, Dismantling, Assembly and Safety Rules.
Important
• Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
Product Type
3" Cut Off Tool
Manufacturer/Supplier
Sioux Tools, Inc.
117 Levi Drive
Murphy, NC 28906
U.S.A.
Tel No. 828-835-9765 Fax No. 828-835-9685
Product Net Weight
1.75 Ibs
0.79 Kg
Recommended Use Of
Balancer Or Support
NO
5564A
Recommended Max.
Hose Length
30 Ft 10 M
RPM
21,000
Cycles Per Min.
CE
Model No/Nos
Serial No.
Recommended Hose Bore
Size - Minimum
1/4 ins 10 mm
Air Pressure
Noise Level: Sound Pressure Level 93.0 dB(A)
Sound Power Level 104.0 dB(A)
Recommended Working 6.2
Maximum 6.2
bar 90
bar 90
PSI
PSI
Test Method: Tested in accordance with Pneurop
test code PN8NTC1 and ISO Standard 3744
WARNING
Less than 2.5 Meters / Sec
2
SAFETY MESSAGES
Avoid Prolonged Exposure
To Vibration
Personal Safety Equipment
Always Read Instructions
Before Using Power Toole
Always Wear Safety
Goggles
SAfety Glasses
YES
YES
Use - Safety Boots
Use - Breathing Masks YES
Use - Ear Protectors YES
Wear Hearing Protection
Safety rules when using a 5564A
Cut Off Tool
- Always wear safety goggles.
- Never use the tool unless the guard is fitted.
- Use accessories rated at 25,000 RPM.
- Prolonged exposure to vibration may cause injury.
- Read all instructions before using this tool. All
operators must be fully trained in its use and aware of
these safety rules.
- Do not exceed the maximum working air pressure.
- Use personal protection equipment as recommended.
- Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicalsknownto cause cancer,birth defectsand other
reproductiveharm.
- Use only compressed air at the
recommended conditions.
- If the tool appears to malfunction,
remove from use immediately and
arrange for service and repair. If it is
not practical to remove tool from
service, then shut off the air supply
to the tool and write or have written a
warning note and attach it to the tool.
- If tool is to be used with a balancer or
other suspension device, ensure that
the tool is firmly attached to the
suspension/support device.
- When operating the tool, always keep
the body and particularly the hands
Vibration Level
Test Method: Tested in accordance with ISO
away from the working attachment fixed to the tool.
- The tool is not electrically insulated. Never use the tool
if there is any chance of coming into contact with live
electricity.
- Always when using the tool, adopt a firm footing and/or
position and grip the tool sufficiently only to overcome
any reaction forces that may result from the tool doing
work. Do not overgrip.
- Use only correct spare parts for maintenance and
repair. Do not improvise or make temporary repairs.
Major servicing and repairs should only be carried out
by persons trained to do so.
- Do not lock, tape, wire, etc. the 'On/Off' valve in 'On'
position. The trigger/lever, etc. must always be free to
return to the 'Off' position when released.
- Always shut off the air supply to the tool and press the
~ .••....•..Take Air From Top
All Pipe And Fittings
Should Be 1/2" Or Larger~
Compressor
with Sufficient Capacity
To Maintain Recommended
Working Pressure At
~tlet
Jo ~
( Receiver Tank
L-....: ~
\40 Gallons Or
=t:
/I \\
Drain Daily
Low Spot To
Trap Water
Easy To Reach And Air Tool
Operate Shut Off Valve
s-:
Air Regulator Set At
Recommended Working
~ Air Pressure
Drain Daily
~
••••v ••
Filter Lubricator
Recommended Air Supply System
PageNo 1
Figure 1