Worx WG150 Manual Del Usuario página 10

IG
white line guides to indicate the cutting line po-
sition. Align these marks with the edge of your
lawn.
While edging allow the tip of the line to make
contact. Do not force the line. The rotation
wheel helps protect the unit and keeps the unit
from contacting the ground.Take extra caution
while edging as objects can be thrown from the
trimmer line.
AUTOMATIC LiNE FEED SYSTEM
When initially switching on thetdmmer, a small
length of line is fed out.
A 'clattering' noise will be heard when the lines
hit the line cutter. DO NOT BE ALARMED this is
quit normal. After about 5 seconds the line will
be cut to the correct length and the noise will
reduce as the motor achieves full speed.
If the noise of the line being cut can't be heard,
more line will be fed out.
To feed more line, it is first necessary to allow
the trimmer to stop completely, then restart, al-
lowing the motor to reach full speed.
Repeat above 4 times until you hear the lines
hitting against the line cutter. (Do not repeat
this procedure more than 6 times)
TO MANUALLY FEED THE LiNE (See L)
If required, line can be feed out manually.
To operate, press and release manual line feed
button (16), whilst gently pull out the line until
the line reaches the line cutter.
If the line extends past the line cutter, too much
line has been fed out.
Iftoo much line isled out, remove the spool cap.
With one hand, rotate the spool anti-clockwise
until it is stopped. Hold the spool in place. With
the other hand, press the line feed button(16)
fully. Continue to rotate the spool a little, then
release the line feed button. The line will then
be shorter. Repeat these steps until the line is
at the desired length.
TO REMOVE THE CAP
Press and hold in the two latches (12) (See M).
Pull cap away from the spool holder.
When refitting the spool cap.
Keep all areas of the cap and spool holder clean.
Press firmly down towards the spool holder to
ensure cap is fully located.
Check that the cap is correctly fitted by trying to
remove it without depressing the two latches.
TO REPU&CE CUT LiNE
For your convenience it is recommended you
buy spool and line complete.
TO FiT SPOOL AND LiNE COMPLETE:
Remove old spool.
Place new spool into cap with cut out areas of
the spoo| in |ine with eye|ets.
Release line from cleat and feed line through
eyelet.
Refit the cap.
TO FIT NYLON LiNE ONLY:
_ arning." Take approximately 16ft of line.
Insert 5/8" of line into the spool holes and
wind line in the direction of the arrows on the
top of the spool.
YourTrimmer is designed to use only line with
a maximum diameter of 0.065"
IMPORTANT :Leave approximately 4" of line
unwound and place into cleat.
Care should be taken to ensure that the line is
neatly coiled on the spool. Failure to do so will
impair the efficiency of the automatic line feed.
Then fit spool as described in "_l'o fit spoo|
and |ine comp|ete'.
MAINTENANCE
After use, disconnect the machine from the
battery and check for damage.Your power tool
requires no additional lubrication or mainte-
nance. There are no user serviceable parts in
your power tool. Battery powered trimmers
should only be repaired by an authorised re-
pairer. Use only manufacturers recommended
replacement parts and accessories.
Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth.
Always store your power tool in a dry place out
of the reach of children. Keep the motor ven-
tilation slots clean. Keep all working controls
free of dust. If you see some sparks flashing in
the ventilation slots, this is normal and will not
damage your power tool.
CTC-WG150-M-060418.indd 10 2006-4-20 14:40:05