Descargar Imprimir esta página

Worx WG150 Manual Del Usuario página 9

Ocultar thumbs Ver también para WG150:

Publicidad

Idiomas disponibles

Idiomas disponibles

The battery pack can then be removed for use in
your trimmer. The charger timer circuit and bat-
tery pack temperature
safety cut-out device pre-
vent overcharge of your battery pack.
_
arning:
After long usage the battery will become
hot, let the hot battery cool down for 1 hour be-
fore recharging.
4.
TO
REMOVE
OR
INSTALL
BATTERY
PACK
Locate latches on side of battery pack and depress
both sides to release battery pack from your grass
trimmer.
Remove battery pack from your grass
trimmer
(See E). After recharge insert the battery
pack into grass trimmer's
battery port. A simple
push and slight pressure will be sufficient.
5 SAFETY
ON/OFF
SWITCH
Your switch
is locked off to prevent
accidental
starting.
Depress lock off button (B) then on/off
switch
(A) and release lock off button (B).Your
switch is now on. To switch off just release the
on/off switch (See F).
_
Warning:
The cutting
bead continues
to rotate
aher
the trimmer
has bee,
switched
off, wait
unti|
it has
stopped
the,
|ay dow,
the too|.
G. ADJUSTMENT
OF THE
TELESCOPIC
SHAFT
(See G)
Unscrew the lower locking knob (4)in the direc-
tion indicated to unlock.
Adjust the length of the telescopic
shaft to the
most comfortable
length.
Tighten the lower locking knob.
7. MAIN
HP_ll)LE
ROTATION
(See H)
Unscrew the upper locking knob (3) in the direc-
tion indicated to unlock.
Adjust the angle of the main handle clockwise
90 degree max.
Turn the upper locking knob in the opposite
di-
rection to lock.
8. AILIUSTUIINT
OF AUXILIARY
HANDLE
Pull up the auxiliary
handle locking lever (5).
Hold the lever and rotate the auxiliary
handle
to the most comfortable
and balanced
position
(See I).
Release the lever, your
auxiliary
handle
has
been locked.
9. ADJUSTMENT
OF THE TRIMMER
HEAD
ANGLE TO THE SHAFT
Use both of your hands, one grips the shaft, an-
other on the head, then apply adequate force to
adjust the trimmer
head to the most comfort-
able position.The
ratchet mechanism
will make
a heavy clicking sound which is normal and not
a defect (See J).
QPERA?IQH
_
Warning:
Always
wear
eye protection.
Never lean over the trimmer
head. Rocks
or debris
can ricochet
or be thrown
into eyes
and face and cause blindness
or other serious
injury. When opening
unit, check for the follow-
ing:
Wear eye protection
and heavy clothing.
Hold
front handle with
one hand and auxiliary
han-
dle with
another
hand. Keep unit below waist
level. Work only from your right to your left to
ensure debris
is thrown
away from you. With-
out bending
over, keep line near and parallel
to the ground (perpendicular
when edging) and
not crowded
into material being cut.
o9
Warning:
Make
sure that
line
is fed
out before
operation.
Make
sure mo_
tot is up to full speed
before
trimming.
_
Warning:
Use
only
0.065"
diameter
cutting
line. Other sizes of line will not
feed properly
and will result
in improper
cut-
ting head function
or can cause serious
injury.
Do not use other material
such as wire, string,
rope, etc.Wire
can break off during cutting
and
become a dangerous
missile that can cause se-
rious injury.
TRIMMING
Hold the bottom
of the trimmer
head about
3.25"(8 cm) above the ground and at an angle.
Allow
only the tip of line to make contact.
Do
not force trimmer
line into work area.
I:DGING
(See K)
Unscrew
the upper locking knob (3) and rotate
the main and auxiliary
handle to 90 ° with cut-
ting head (See H).
Retighten the upper locking knob.
Adjust
trimmer
head angle to be the lowest
horizontal
setting. Then position
the wheel
on
the ground for edge mode.The
guard has two
CTC-WG150-M-060418Jndd
g
2006-4-20
14:40:04

Publicidad

loading