Publicidad
Idiomas disponibles
Idiomas disponibles
Menu Item
Description
[Crossover]
Select a speaker unit (filter) to adjust the HPF or LPF cutoff
frequency and the slope for each speaker unit (page 49).
[Subwoofer Settings]
Select the subwoofer phase (page 49).
[Listening Position]*1
Select a listening position that you want to make as the
[Off] [Front Left] [Front
centre of sound effects.
Right] [Front] [All]
[Time Alignment]
Select or customise the time alignment settings to reflect
[On] [Off]
the distance between the listener's position and each
Listening position*1*2
speaker. You need to measure the distance between the
[Off] [Front Left] [Front
head of the listener and each speaker unit.
1
Right] [Front] [All]
Touch
Standard Mode*3*4
select the alignment speaker.
2
[Front Left] [Front Right]
Touch
[Rear Left] [Rear Right]
selected speaker and listening position.
[Subwoofer]
TIP
Network Mode*3*4
If you touch [TA On], the time alignment is turned off mandatorily.
[High Left] [High Right]
[Mid Left] [Mid Right]
NOTE
[Subwoofer]
This function is available only when the listening position setting
Distance
is set to [Front Left] or [Front Right].
[0] to [350]
[Auto EQ]
Set the auto-adjusted equaliser to suit the vehicle's
[On] [Off]
acoustics. To use this function, the Auto EQ measurement
must be done in advance (page 48).
[A-EQ&TA Measurement]
Measures and adjusts the vehicles acoustics, equaliser, and
time alignment automatically to suit the vehicle interior
(page 48).
[Save Settings]
Save to recall the following current sound settings by
touching [OK]: bass boost, slope, subwoofer phase, speaker
level, Graphic EQ, HPF/LPF, listening position, crossover,
time alignment.
TIP
When you touch [Cancel], return to the [Audio] setting screen.
[Load Settings]
Load the sound settings.
NOTES
• [Sound Setting] is available only when you have already saved
the sound settings (page 47).
• [Auto EQ&TA Setting] is available only when you have already
performed Auto EQ measurement (page 47).
or
to select the listening position then
or
to input the distance between the
Menu Item
Description
[ASL]
Set to one of five levels to increase the volume level of the
audio depending on the driving speed and road
conditions.
[Bass Boost]
Adjust the bass boost level.
[0] to [6]
[Rear Speaker Output]
Select the rear speaker output.
[Rear] [Subwoofer]
NOTES
• This function is available when [Standard Mode] is selected as
the speaker mode.
• If [Subwoofer] is selected, the rear speaker adjustment is not
available in [Speaker Level], [Time Alignment] and [Crossover].
[Loudness]
Compensates for deficiencies in the low-frequency and
[Off] [Low] [Mid] [High]
high-frequency ranges at low volume.
[Automatic Level Control]
Corrects automatically the audio level difference between
the music files or the sources.
[Off]
Turns the auto level control setting off.
[Mode1]
Corrects a little the audio level difference between the
music files or the sources (for the narrow dynamic range
audio signal).
[Mode2]
Corrects widely the audio level difference between the
music files or the sources (for the wide dynamic range
audio signal).
[Sound Retriever]
Enhances compressed audio and restores rich sound
[Off] [Mode1] [Mode2]
automatically.
TIP
[Mode2] has a stronger effect than [Mode1].
*1 [All] is not available when [Network Mode] is selected as the speaker mode.
*2 If you change the listening position setting, the output levels of all the speakers will change in
conjunction with the setting.
*3 To use this function, the vehicle's acoustics must be measured in advance.
*4 This function is available only when the [Listening Position] setting is set to [Front Left] or [Front
Right].
Adjusting the equaliser curve automatically (Auto EQ)
By measuring the vehicle's acoustics, the equaliser curve can be adjusted automatically
to suit the vehicle interior.
47
En
Publicidad
