Remington RM5520R Manual De Instrucciones página 8

_J ARNING:
Do not let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come |
in contact with plastic part& These chemicals may damage, weaken and destroy plastic, which may
1
result in serious personal injury.
CLEANING INSTRUCTIONS
1. Stop the engine and wait for all moving parts to stop. Cylinder Fins
2. Allow the unit to coo!.
3. Slacken the chain !f it was retensioned at operating temperature
during cutting work. The chain contracts as it cools down. If it is
not slackened, it may damage the gearbox and bearings.
4. Wipe the unit down with a damp cloth. Do not douse the unit with
water. Do not use solvents or strong detergents. If preparing the
unit for long-term storage (three months or more), remove the
chain and guide bar, then clean the unit thoroughly with a damp
cloth. A firm-bristled, non-wire, brush can be used to remove
debris from the bar groove and assembly. When finished,
reassemble the unit. Refer to Removing!Replacing the Guide Bar
and Chain. Fig. 54
5. Debris must be removed from the cylinder fins on a regular basis to reduce the risk of damage to the unit and
personal injury from fire. Use compressed air, at 40 PSI or !ower, to blow debris from the cylinder fins (Fig. 54).
A!ways wear safety goggles!glasses when cleaning the cylinder fins with compressed ain Use a small wire brush to
dislodge stubborn debris. Do not use water or solvents on the cylinder fins. If there is a significant amount of debris
that remains after cleaning, have the cylinder fins cleaned by an authorized service dealer.
6. Spray the guide bar and chain with corrosion inhibiting oil
STORAGE INSTRUCTIONS
NOTE: !t is normal for oil to seep from the unit when it is not in use. Please take this into consideration when storing
the unit.
1. Follow the Cleaning Instructions listed above.
2. Attach the scabbard to the guide bar and chain.
3. Store the unit in a dry, high and/or locked location, out of the reach of children and other unauthorized persons.
Always store the unit and fuel in a cool, weIFventilated space where fuel vapors cannot reach sparks or open
flames from water heaters, electric motors or switches, furnaces, etc. Never store the unit, with fuel in the tank,
inside a building where fumes may reach an open flame or spark.
Long-term Storage Instructions
In addition to the standard storage instructions described above,
perform the following steps when storing the unit for 30 days or more:
1. Drain the fuel tank by running the unit dry. Alternatively, tip the
engine housing/fuel tank over to pour the fuel mixture into a
suitable container and then run the engine until it stops in order to
remove fuel from the carburetor.
2. Allow the engine to cool.
3. Remove the spark plug. Refer to Inspecting/Adjusting!Replacing
the Spark Plug=
4. Pour 1 teaspoon or clean 2-cycle oil into the combustion chamber
(Fig. 55). Pull the starter rope slowly several times to coat the
internal components.
5. Replace the spark plug. _ig.55
Removing a Unit From Long-term Storage
1. Remove the spark plug.
2. Pull the starter rope briskly to clear excess oiI from the combustion chamber.
3. Clean and gap, or replace, the spark plug.
4. Prepare the unit for operation.
CAUSE SOLUTION
o _ 0 = ,= ." he _ e o =
The carburetor mixture adjustment setting is incorrect Have the carburetor adjusted by an authorized service
center
The fuel tank is empty
The choke lever is in the wrong position
The air fi!ter is dirty
The air filter is plugged
The fuel is old and!or improperly mixed
Fill the fuel tank with properly mixed fuel
Q
Move the choke lever to Position 2
Clean the air filter
Clean or replace the air filter
O_D
Drain the fuel tank and add fresh, properly mixed fuel
iii ii_ii
The spark plug is fouled Clean, gap or replace the spark plug
iiii
The spark arrestor screen is plugged Clean the spark arrestor screen
The fuel mixture !s incorrect
D =,= , D , ,_ " = e
The bar lube reservoir is empty
The oil flow from the automatic oiler to low
Drain the fuel tank and add fresh, properly mixed fue!
! ii{i i i 'i:_
Refill the bar lube reservoir
.......
increase the oil flow from the automatic oiler
, DO 0 _0 ' €" =
The guide bar and chain are assembled incorrectly Refer to Removing/Replacing the Guide Bar and Chain
The drive assembly is damaged Refer to Service Information
The chain is on backwards Reverse the direction of the chain
NOTE: For repairs beyond the minor adjustments listed above, locate your nearest authorized service center by
calling the Customer Support Department at 1=866-206=2707 (U.S.) or t=877=696_5533 (Canada},
Engine Type ..................................................................... Air-Cooled, 2-Cycle
Displacement ...................................................................... 55 cc (3.36 cu in)
Idle Speed .............................................................................. 2,800 rpm
Operating Speed ......................................................................... 8,500 rpm
Ignition Type ............................................................................. Electronic
ignition Switch ......................................................................... Slide Switch
Starter ..................................................................... AST Starting Auto Rewind
Throttle Control .................................................................... Finger-Tip Trigger
Throttle ....................................................................... Manual Spring Return
Spark Plug Gap .................................................................. 0.025 in (0.635 ram)
Carburetor ................................................................... Diaphragm, AIFPosition
Muffler .......................................................................... Baffled with Guard
Drive Sprocket ............................................................................. 6-Tooth
Lubrication ........................................................................ Bar and Chain Oil
Bar Lube Reservoir Capacity ........................................................... 6.8 fl oz (201 ml)
Fuel/Oil Ratio ................................................................................. 40:1
Fuel Tank Capacity ................................................................ 16,6 fl oz (496.8 ml)
Cutting Diameter ..................................................................... 36 in (91.4 cm)
Bar Length .......................................................................... 20 in (50.8 cm)
Chain Pitch .......................................................................... 3/8 in (9.5 mm)
Chain Gauge ....................................................................... 0.05 in (1.27 mm)
Approximate Unit Weight (no fuel) ....................................................... 17.5 Ibs (7.9 kg)
* All specifications are based on the latest product information available at the time of printing. We reserve the right
to make changes at any time without notice.
REPLACEMENT PARTS
Part # Description
753-06267 .................................... 20-inch Chain
753-06266 .................................... 20-inch Guide Bar
783-06270 .................................... Bar Lube Reservoir Cap
753-06271 .................................... Bar-retaining Nuts
753-06272 .................................... 8 oz Bar and Chain Oil