Ninja BN800 Serie Manual Del Propietário página 4

USING THE TOTAL CRUSHING® PITCHER
IMPORTANT:
• Review all warnings at the beginning of this Owner's Guide before proceeding.
• As a safety feature, if the pitcher and lid are not properly installed, the timer will display "... ..." and
the motor will be disabled. If this happens, repeat step 5 on this page. When the pitcher and lid are
properly installed, the program button LEDs will illuminate, indicating the appliance is ready to use.
NOTE:
• If the Stacked Blade Assembly is not fully seated, you will not be able to install and lock the lid.
• The pitcher lid handle will not fold down unless it is attached to the pitcher.
1
Plug in motor base and place on a clean, dry, level surface such as a
countertop or table.
2
Lower the Total Crushing Pitcher onto the motor base. The handle
should be aligned slightly to the right and the pitcher should be
oriented so the LOCK symbols are visible on the motor base.
Rotate the pitcher clockwise until it clicks into place.
3 Exercising care, grasp the Stacked Blade Assembly by the top of
the shaft and place it onto the drive gear inside the pitcher. Note
that the blade assembly will fit loosely onto the drive gear.
4 Add ingredients to the pitcher. DO NOT add ingredients past the
MAX LIQUID line.
5
Place the lid on the pitcher, aligning the triangle symbol on the lid with the
triangle symbol on the handle. Press down on the handle until it clicks into
place. The triangle symbols MUST be aligned for the lid to lock and the unit to
operate. Once the lid is locked in place, press the Power button to turn unit on.
The available program buttons will illuminate and the unit will be ready for use.
6a If using an Auto-iQ® program, first select the program that best
suits your recipe. The preset feature will automatically stop at the
end of the program. To stop the unit at any time, press the
currently active button again.
6b If using a manual program, select your desired speed. Once the
ingredients have reached your desired consistency, press the
active button again, or wait 60 seconds for the unit to come
to a complete stop.
7 To remove the pitcher from the motor base, turn the pitcher
counterclockwise and then lift up.
8a To pour out thinner mixtures, ensure the lid is locked in place,
then open the pour spout cap.
8b For thicker mixtures that cannot be emptied through the pour
spout, remove the lid and Stacked Blade Assembly before
pouring. To remove the lid, press the RELEASE button and lift
the handle. To remove the blade assembly, carefully grasp it by
the top of the shaft and pull straight up. The pitcher can then
be emptied.
9 Turn the unit off by pressing the Power button. Unplug the unit
when finished. Refer to the Care & Maintenance section for
cleaning and storage instructions.
ninjakitchen.com ninjakitchen.com
USING THE SINGLE-SERVE CUP
IMPORTANT: Review all warnings at the beginning of this Owner's Guide before proceeding.
1 Plug in motor base and place on a clean, dry, level surface such
as a countertop or table.
2 Add ingredients to the Single-Serve Cup. DO NOT add ingredients
past the MAX LIQUID line on the cup.
3 Install the Pro Extractor Blades® Assembly onto the top of the
cup. Twist the lid clockwise until it's sealed tightly.
4 Turn the cup upside down and install on the motor base. Align the tabs on
the cup with the slots on the base, then rotate cup clockwise until it clicks
into place. Once the cup is locked in place, press the Power button to turn
unit on. The available program buttons will illuminate and the unit will be
ready for use.
5a If using an Auto-iQ® program, first select the program that best suits your
recipe. The preset feature will automatically stop at the end of the program.
To stop the unit at any time, press the currently active program again.
5b If using a manual program, select your desired speed. Once the ingredients
have reached your desired consistency, press the active button again, or
wait 60 seconds for the unit to come to a complete stop.
6 To remove the cup from the motor base, turn the cup counterclockwise
and then lift up.
7 Remove the Pro Extractor Blades Assembly by twisting the cap
counterclockwise. DO NOT store blended contents with Pro Extractor
Blades Assembly attached. Exercise care when handling the blade
assembly, as the blades are sharp.
8 Turn the unit off by pressing the Power button. Unplug the unit
when finished. Refer to the Care & Maintenance section for
cleaning and storage instructions.
9 To enjoy your drink on the go, place the Spout Lid onto the cup
and twist lid clockwise until firmly sealed. For storing ingredients
in the cup, use only the Spout Lid to cover.
ninjakitchen.com ninjakitchen.com