Publicidad
Idiomas disponibles
Idiomas disponibles
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for differ-
ent applications, with different accessories or insertion tools
or is poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over the
total working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched off
or when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
EC-Declaration of Conformity
We declare under our sole responsibility that the product
described under "Tool Specifications" is in conformity with all
relevant provisions of the directives 2011/65/EU,
2014/30/EU, 2006/42/EC including their amendments
and complies with the following standards:
EN 60745-1, EN 60745-2-4.
Technical file (2006/42/EC) at:
Adolf Würth GmbH & Co. KG, PCM,
Reinhold-Würth-Straße 12–17
74653 Künzelsau, Germany
Marcel Strobel
Head of Product
Management
Künzelsau: 31.08.2014
Battery Charging
Note: The battery supplied is partially charged. To ensure
full capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the first
time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
Dr.-Ing. Siegfried Beichter
Head of Quality,
Authorized Signatory
Removing the battery
To remove the battery 2, press the unlocking buttons 1 and
pull the battery out of the machine to the rear. Do not exert
any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator 4
indicate the charge condition of the battery 2. For safety rea-
sons, it is only possible to check the status of the charge con-
dition when the machine is at a standstill.
To indicate the charge condition, press and hold button 3 of
the switched off machine.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
Changing the Tool
Before any work on the machine itself (e.g.
maintenance, tool change, etc.) as well as dur-
ing transport and storage, remove the battery
from the power tool. There is danger of injury when
unintentionally actuating the On/Off switch.
Wear protective gloves when changing appli-
cation tools/accessories. Contact with the applica-
tion tool/accessory can lead to injuries.
Mounting/Replacing the Application
Tool/Accessory
If required, remove an already mounted application tool/
accessory.
For removing the application tool/accessory, loosen the
screw 11 with the hex key 12 and remove the application
tool/accessory.
Insert the supplied adapter by allowing the smooth side of the
adapter to engage on the cams of the tool holder 8 (see fig-
ure on the graphics). Mount the application tool/accessory
on the adapter at any position.
Fasten the application tool/accessory with bolt 11. Tighten
the bolt with hex key 12 until the spring washer of the bolt
faces flush against the application tool/accessory.
Check the tight seating of the application
tool/accessory. Incorrect or not securely fastened
application tools/accessories can come loose during
operation and pose a hazard.
Capacity
2/3
1/3
<1/3
Reserve
14
Publicidad
