Dreame Vortech Z10 Manual De Usuario página 12

Product Overview
EN
Accessories
1. Multi-Surface Brush
2. Dust-Removal Hub
3. Base
4. Soft Roller Brush
5. Extension Rod
6. Soft Dusting Brush
7. Combination Tool
8. Dust Collection Bag
(x1 pre-installed, x1 stored in the
packaging box)
9. Motorized Mini-Brush
10. Accessory Mount
11. Accessory Bag (Screw * 2 + Hex Key * 1)
Fig. A-1
Component Names
1. Display Screen
2. Dust Cup
3. Dust Cup Vent
4. Dust Cup Release Button
5. Multi-Surface Brush
6.
Power Button
(Press to turn on/Release to turn off)
7. Battery Status Indicator
8. Antistatic Contact
9. Battery Pack Release Button
10. Charging Contacts
11. Extension Rod Release Button
12. Extension Rod
13. Brush Release Button
Fig. A-2
Note: The illustrations in this manual are
indicative only. The actual product may
differ.
Dust-Removal Hub
1. Dust Collection Button
Dust Collection Status Indicator
• Solid Green
The dust-removal hub is in standby
mode
3
• Blinking Green
The dust-removal hub is prepared to
collect dust
• Solid Orange
The dust collection bag uninstalled or
inappropriately installed
• Blinking Orange
The dust collection bag reaches capacity /
the air duct is blocked
2. Dust Collection Bag
3. Magnetic Cover
4. Dust-Removal Hub Vent
5. Charging Contacts
6. Dust Cabinet Filter
7. Air Outlet Filter
8. Power Cord
Fig. A-3
Installation
Dust-Removal Hub Installation
Assemble dust-removal hub onto the base,
and use the hex key in the accessory bag
to tighten the screw.
Fig. B-1
Accessories Installation
Click
Fig. B-2
Note:
• It is not recommended to use the
motorized mini-brush with the extension
rod.
• Please install the accessories according
to the actual cleaning needs.
Charging
Charging with the Dust-Removal
Hub
Note:
• Fully charge the vacuum before using it
for the first time.
• The vacuum cannot be used while
charging. This will take about 3.5 hours.
• Vacuuming at Turbo mode for a
prolonged period will cause the battery
to heat up, which increases charging
time. Allow the vacuum to cool down for
30 minutes before charging it.
• When the vacuum is not in use, it can be
placed on the dust-removal hub.
• The outlet of the power cord can be
adjusted according to users' needs.
Fig. C-1
Battery Status Display
Display Screen
The number on the display screen
represents the current battery level in a
percentage during charging. When the
number becomes 100, the battery is fully
charged.
Fig. C-2
Battery Status Indicator
Charging
Fully charged Charging
Standby Mode
Discharging
Battery Level ≥ 10%
Battery Level ＜ 10%
Solid white
Blinking white Off
Fig. C-3
How to Use
Display Screen
1. Trigger Switch Lock
Press briefly to enter/ exit the lock state.
2. Suction Level
The color of fan-shaped icon changes
with different modes.
3. Lock Status
4. Battery Level Percentage
When the display shows "LO", it indicates
that the battery level is lower than 10%.
5. Suction Level Switch
Press briefly to switch between eco, med
and turbo mode.
Note: The Med mode is used by default
every time the vacuum is turned on.
Charging/Battery Level Indicator
Low Battery Level
Blinking red: Battery level ≤ 10%
Out of Battery
Blinking red: Battery level ＝ 0%
Charging
Breathing red: Battery level ≤ 10%
Breathing green: Battery level ＞ 10%
Fig. D-1
Suction Level
Med Eco Turbo
Fig. D-2
EN
4