Dreame Vortech Z10 Manual De Usuario página 13

Troubleshooting
EN
If the vacuum is not working properly, the screen display will show an error message.
Please refer to the troubleshooting table to find your solution.
Error Icon Status
Blinking orange Air duct blocked
Blinking orange Brush roller stuck
Solid orange Filter is expiring
Blinking red
If one of the error codes from E0 to E4 appears on the display screen, please contact the
after-sales service team.
Working Methods
Select from two working methods for the vacuum, which can be selected based on your
own needs.
Method 1: Discontinuous Cleaning Mode
Press and hold the power button to start the appliance, and release the button to stop
immediately.
Fig. D-3
Method 2: Continuous Cleaning Mode (Trigger Switch Lock)
Press the trigger switch lock to switch to Continuous Cleaning Mode, and then briefly
press the power button to keep the vacuum in Continuous Cleaning Mode.
Note:
• Use the trigger switch lock to free your fingers from fatigue caused by holding the
switch.
• Press the trigger switch lock again to quit Continuous Cleaning Mode.
Fig. D-4
5
Error Message Solutions
Check whether the dust cup,
extension rod, multi-surface brush,
soft roller brush or motorized mini-
brush is blocked.
Refer to the [Cleaning the Multi-
Surface Brush] section to clean the
debris and hair tangled on the brush
roller.
Please replace the filter in time.
High-
Please wait until the motor
temperature
temperature returns normal.
alert
How to Use
Starting Dust Collection
1. Place the dust-removal hub near a
power outlet and put the plug into it.
2. Place the vacuum on the dust-removal
hub (the vent of the dust cup should be
aligned with that of the dust-removal
hub) until you hear a click.
3. Press the dust collection button.
Fig. D-5
Note:
• The dust collection process cannot be
stopped by pressing the dust collection
button.
• If there is a lot of garbage in the dust
cup, please perform the dust collection
process several times to achieve better
cleaning results.
• If the dust collection bag reaches
capacity or the air duct is blocked during
the dust collection process, the dust-
removal hub will stop working after the
process is completed and cannot collect
dust again.
Using Different Accessories
Multi-Surface Brush
Note:
• The multi-surface brush can be attached
directly to the vacuum.
• When the appliance starts, the
lights in front of the brush roller
will automatically turn on, which is
convenient for use.
-
When using on baby play mats, carpets
or for vacuuming coffee beans, pop corn
and other pellets, turn on the switch on
the brush.
-
When vacuuming on tiles, wooden
floors or other hard surfaces, turn off the
switch.
Fig. D-6
Soft Roller Brush
Suitable for cleaning hard floors such as
marble and tile.
Fig. D-7
Motorized Mini-Brush
For vacuuming dirt, pet hair, and other
stubborn debris from sofas, bedding, and
other fabric surfaces.
Note: It is not recommended to vacuum
on fragile surfaces, such as silk.
Fig. D-8
Soft Dusting Brush
Suitable for vacuuming on LCDs, keyboards,
lampshades, curtains, shutters and other
surfaces of fragile objects.
Fig. D-9
Combination Tool
Suitable for vacuuming cracks, corners of
doors and windows, stairs, and other hard-
to-reach places.
Fig. D-10
Accessory Mount
The soft dusting brush, combination tool
and motorized mini-brush can be placed
on the accessory mount when not in use.
Fig. D-11
Note:
• If any rotating part becomes stuck, the
vacuum may shut off automatically.
Remove any trapped foreign objects,
then resume use.
• When the battery becomes overheated,
the vacuum will automatically shut
off. Wait until the battery temperature
returns to normal, then resume use.
Care & Maintenance
Tips:
• Always use genuine parts to keep your
warranty from being void.
• If the filter or nozzle becomes clogged,
the vacuum will stop working shortly
after being turned on. Clear the tube to
restore functionality.
EN
6