Publicidad
Idiomas disponibles
Idiomas disponibles
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger firmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after
use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period is
not activated, the electric discharge might be low when
using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life
will become shorter.
(2) Avoid recharging at high temperatures. A rechargeable
battery will be hot immediately after use. If such a
battery is recharged immediately after use, its internal
chemical substance will deteriorate, and the battery life
will be shortened. Leave the battery and recharge it
after it has cooled for a while.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Remaining battery indicator
Charging a USB device from a
electrical outlet
Charging a USB device and battery
from a electrical outlet
How to recharge USB device
Selecting accessories
ASSEMBLY PROCEDURES
WARNING
Pull out battery before doing any assembly.
1. Installing of handle (Loop handle type) (Fig. 7)
Attach the handle to the main pipe with the angle
towards the grip side.
Adjust the location to the most comfortable position
before operation.
Make sure to securely attach the handle with the
2 bolts.
NOTE
Install the loop handle between the arrow marks on the
handle location label.
2. Installing of guard
WARNING
If an incorrect or faulty guard is fitted, this may cause
serious personal injury.
CAUTION
The guard extension is equipped with the knife. Be
careful with handling it.
Align the guard with the cover bracket and secure it to the
main pipe, using the bolt and cover bracket. (Fig. 8)
NOTE
○ The guard extension is already attached to the guard at
the time of purchase.
○ The cover bracket may come already mounted to the
gear case.
3. Installing the shoulder belt
WARNING
○ Be sure to attach the shoulder belt so that the brush
cutter can be carried correctly.
○ If you get the feeling the tool is not operating normally,
turn off the motor immediately, remove the quick-
release bracket of the shoulder belt and remove the
tool.
CAUTION
○ If you do not support the tool when you pull the quick-
release belt, it may fall causing injury or damage. Hold
the main pipe with one hand while you pull with the
other hand.
○ Make sure the quick-release function operates normally
before you start working.
○ Before attaching, check to confirm that the belt is not
cut, frayed, or damaged.
○ Check to confirm that the hook and hanger are neither
deformed nor damaged.
○ Once attached, press down on the main unit to confirm
that the hook does not detach easily and that the
shoulder belt is not loose.
○ Check to confirm that the quick release function
operates as it should.
(1) Place the shoulder belt on the shoulder as shown in
Fig. 9 and engage it with the hanger on the tool. Adjust
Figure
Page
the shoulder belt to suitable length.
NOTE
5
3
You may need to adjust the position of the hanger to
balance the unit. To do so, loosen bolt and adjust the
6
4
position of hanger. After adjusting as necessary, make
sure to securely tighten the bolt. (Fig. 10)
23
7
(2) To remove the tool from the shoulder belt, support the
tool by holding the main pipe with one hand and use the
24-a
7
other hand to pull the quick-release belt as shown in
Fig. 11 to free it from the bracket.
(3) To strap on the tool, insert the bracket in the hook and
24-b
7
insert the quick-release bracket over the hook and into
the wide opening of the bracket. (Fig. 12)
25
7
Gently pull the shoulder belt to make sure that it is
properly attached.
—
372
4. Installation of cutting attachment
WARNING
○ Install the cutting attachment properly and securely as
instructed in the handling instructions.
If not attached properly or securely, it may come off and
cause serious and/or fatal injury.
○ Always use genuine HiKOKI cutting attachments and
metal fittings.
[Installation of semi-auto nylon head]
WARNING
For HiKOKI heads, use only flexible, non-metallic line
recommended by the manufacturer. Never use wire or
wire ropes. They can break off and become a
dangerous projectile.
(1) Function
Automatically feeds more nylon cutting line when it is
tapped at low rpm (not greater than 4000 min-
19
English
1
).
Publicidad
