Broan EVOLUTION 3 QP3 Serie Manual Del Usuario página 4

BR N
QP3 SERIES
MAKE-UP AIR DAMPER
The hood is compatible with Broan Make-Up Air Damper Model
MD6T or Model MDST (optional). Purchase separately.
Make the connection to the Make-Up Air Damper with low volt-
age wiring, as shown. See Make-Up Air Damper instructions for
additional information.
®
BACK OF HOOD
LOW-VOLTAGE CONNECTOR
FOR MAKE-UP AIR DAMPER
Page 4
Stainless Steel Cleaning
DO:
• Regularly wash with clean cloth or rag soaked with warm water
and mild soap or liquid dish detergent.
• Always clean in the direction of original polish lines.
• Always rinse well with clear water (2 or 3 times) after cleaning.
Wipe dry completely.
• You may also use a specialized household stainless steel cleaner.
DON'T:
• Use any steel or stainless steel wool or any other scrapers to re-
move stubborn dirt.
• Use any harsh or abrasive cleansers.
• Allow dirt to accumulate.
• Let plaster dust or any other construction residues reach the
hood. During construction/renovation, cover the range hood to
make sure no dust sticks to the stainless steel surface.
RANGE
HOOD
LOW- V OLTAG E
WIRES
¢----
120
VAC__
MAKE-UPAIR
DAMPER
DAMPER
MOTOR
Avoid: When choosing a detergent
• Any cleaners that contain bleach will attack stainless steel
• Any products containing chloride, fluoride, iodide, bromide
will deteriorate surfaces rapidly.
• Any combustible products used for cleaning, such as ac-
etone, alcohol, ether, benzol, etc. are highly explosive and
should never be used close to a range.
LIGHT BULB REPLACEMENT
REMOTE CONTROL
The hood is compatible with Broan RF Remote Control Model
BCR1 (optional). Purchase separately.
CLEANING AND MAINTENANCE
Proper maintenance of the Range Hood will assure proper per-
formance of the unit.
Motor
The motor is permanently lubricated and never needs oiling. If
the motor bearings make excessive or unusual noise, replace
the motor with the exact service motor. The impeller should also
be replaced.
Grease Filter
The grease filters should be cleaned frequently. Use a warm dish-
washing detergent solution. Grease filters are dishwasher safe.
Clean all-metal filters in the dishwasher using a non-phosphate
detergent. Discoloration of the filters may occur if using phosphate
detergents, or as a result of local water conditions - but this will
not affect filter performance. This discoloration is not covered by
the warranty.
See Step 9 on page 6 for removal and installation instructions.
Non-ducted Recirculation Filters
The non-ducted recirculation filter should be changed every 6
months. Replace more often if your cooking style generates extra
grease, such as frying and wok cooking.The special "Clean Sense"
feature indicates when the filter is to be replaced. The dotted lines
on the indicator strip will change to solid wide lines when it is time
to change the filter. The "Clean Sense" feature works best when
facing toward the cooking surface. See Step 15 on page 7, for
removal and installation instructions.
SUCTION
CU P TOOL
LIGHT PANEL
REWS
LIGHT PANEL
CAUTION: Bulbs may be hot. Always allow bulbs
to cool down before removing them.
This hood uses (4)_en Bulbs (included with hood). Use 120
V, 50W, shielded halogen bulbs - MR16 with GU10 base.
NOTE: Suction Cup Tool (included with hood) can be used to
install and remove light bulbs.
Align pins on bulb with large diameter opening on socket, then
push bulb in towards hood and rotate clockwise until firmly seated.
The position of the bulb socket (depth) is adjustable and may
require adjustment when:
a) certain brands of bulbs are difficult to install.
b) the bulb protrudes too far below the light panel.