Publicidad
Idiomas disponibles
Idiomas disponibles
package).
1) Use two screws and wing nuts to connect
both ends ofthe
bag support
ring. Place the
hardware
in a position that allows the bag
support
ring to best fit the paper bag you are
using (See Fig I).
2) insert the bag support
ring in the bag just
below the fill line. (See Fig J)
3) Fold the paper bag inside along the fill line
of the bag. (See Fig K1,K2)
5. FiTTiNG
A COLLECTION
BAG
1).When
using a paper bag with support
ring,
place the bag into the stand from the top. (See
Fig L1)
2). If you use a plastic collection
bag, roll it
over the top of the stand like you would with
trash bag being used on a trash can. (See Fig
L2)
6. REMOVING
A FULL COLLECTION
RAG
1).When
the bag is full, turn offthe
mulcher
then unplug
it. Lift the mulching
power head
from the stand.(See Fig. L3)
2). Lift the stand off of the collection
bag from
the top. (See Fig.L4)
QPERAT[0N
11.ON/OFF
SWITCH
The ON/OFF switch is located on the lower
side of the motor housing
portion of the
power head.To turn on, pull out the switch.
(See Fig.M1)
To turn off, push the switch in. (See Fig.M2)
_
CAUTION:
To prevent
to
exposure
dusty
warm
air don'_ stand in front
of the motor
wentilation
slots.
2. LOADING
YOUR MACHINE
With the mulcher running,
feed double
handfuls
of dry leaves, or single handfuls
of
wet leaves, into the funnel. Allow the machine
to shred the load completely
and regain speed
before inserting
the next handful. Do not
overload
the machine
by letting it labor at low
speed: this may cause the motor to stop. If
this happens, turn the switch off, unplug the
machine, clear the unshredded
material from
the funnel, restart the machine,
and continue
with
your
shredding.
WARNING.
w Filling
mulcher
with
unshredde(|
material
at a rate
faster
than
the
machine
can
handle
may
result
in
permanent
damage
to your
motor.
AJways
wear
protective
glasses
and
a
mask.
MAINTENANCE
1. CLEANING
YOUR UNIT
Your unit requires a minimum
of maintenance
other than cleaning.
It is recommended
that
you clean out built -up residue inside the
housing
area during
and after each use. When
fully disassembled,
clean the funnel cover
and funnel with clean water, while
using a
dry cloth to clean the motor housing.
Replace
cutting line as often as necessary and clean
air filter frequently.
Any other maintenance
or
repairs should
be performed.
_
AUTION:
Directly
cleaning! the
motor
housing
with
water
will
lead
to permanent
damage
to the motor.
2. REPLACI_MENT
OF CUTTING
LINE
(See Fig. N}
Replace cutting
line (e) when a noticeable
decrease in shredding
efficiency
in observed.
To remove used cutting
lines, cut the old lines
and pull the remaining
line out ofthe
spinner
head (f).When
installing
new cutting
lines
place each end ofthe
new linethrough
the
two holes in the post on top of the spinner
head and through
so that both ends of the line
are even. Then thread the lines through
each
corresponding
ferrule so that both ends of
the line are even.
Note: there is a built in line
cutter that will cut and trim lines shortly
longer
than desired.
WARNING."
For optimum
performance
use only WORX
branded
replacement
lines.
Aftermarket
monofllament
lines
having
max
diameter
of O.O9" |2.1ram)
diameter
maximum
length
of 13.8"
long
could he
temporarily
substituted.
Use of thicker
lines,
lines
made
of substitute
material,
or lines
greater
than
13.8"
long
may
Publicidad
