GE PFW870 Manual Del Propietario E Instalación página 20

Care and cleaning
Water Supply Hoses
Periodically inspect all water inlet hoses for water leaks, wear, cuts, corrosion, and bulges. Replace all hoses immediately
if any sign of these failures appear. All hoses should be replaced every 5 years of use to reduce risk of hose failures
and possible water damage. When replacing hoses, refer to the Installation Instructions for proper installation. DO NOT
overtighten or cross thread fittings. DO NOT allow the hose to rub against sharp objects, become kinked, or become
over stretched. Always ensure hose rubber gaskets are installed and free from leaks when pressurized.
Exterior
Immediately wipe off any spills. Wipe or dust spills or washing compounds with a damp cloth. Washer control panel
and finishes may be damaged by some laundry pretreatment and stain remover products. Apply these products
away from the washer. The fabric may then be washed and dried normally. Damage to your washer caused by these
products is not covered by your warranty. Do not hit surface with sharp objects.
Interior
Dry around the washer door opening, flexible gasket (including attached hoses) and door glass. These areas should
always be clean to ensure a watertight seal. You will notice if you regularly use the ULTRAFRESH VENT System that
this will not be required as often. It is recommended to rinse the washer at least once per month with 1 cup of bleach
(or other commercially available product manufactured for this purpose, such as Tide
poured directly into the basket without clothes and using the Self Clean Cycle.
Self Clean
To clean the interior of the washer,
select the SELF CLEAN feature on the
control panel. This Self Clean cycle
should be performed, at a minimum,
once per month or about every 40 wash
cycles. This cycle will use more water,
in addition to bleach, to control the
rate at which soils and detergents may
accumulate in your washer.
NOTE: Read the instructions below
completely before starting Self Clean cycle.
1. Remove any garments or objects from the washer and
ensure the washer basket is empty.
2. Open the washer door and pour
one cup or 250 ml of liquid bleach
or other washing machine cleaner
into the basket.
3. Close the door and select the SELF CLEAN cycle.
Push the Start pad.
4. When the Self Clean cycle is working, the display will
show the estimated cycle time remaining. The cycle will
complete in about 90 minutes. Do not interrupt the cycle.
Door Gasket
Open the washer door. Using
both hands, press down the
door gasket.
While holding down the door
gasket, inspect the interior
fold. Remove any foreign
objects if found trapped
inside this gasket.
20
5. After the cycle is complete (on some models), the
Video
washer will automatically start an ULTRAFRESH VENT
operation so that the door can remain closed until the
next time you use the washer.
If for any reason the cycle needs to be interrupted, the
door will not open immediately. Forcing open the door at
this stage may cause water to flood. The door will open
after the water is drained to a level where it would not
Scan this code
to watch a video flood the floor.
on this topic.
Self Clean may be interrupted by pressing the Start pad
in between cycles. A power outage in the house might
also interrupt the cycle. When the power supply is back,
the Self Clean cycle resumes where it had stopped.
When interrupted, be sure to run a complete Self Clean
cycle before using the washer. If the Power pad is
pressed during Self Clean, the cycle will be lost.
IMPORTANT:
• Run Self Clean with one Cup (250 ml) of bleach once
a month.
• After the completion of a Self Clean cycle, the interior
of your washer may have a bleach smell.
• It is recommended to run a RINSE & SPIN or a light
color load after the Self Clean cycle.
Make sure there is nothing blocking the
holes behind the gasket.
When you are finished cleaning the
door gasket, release it and the gasket
will return to the operating position.
Washing Machine Cleaner)
®
Video
Scan this code
to watch a video
on this topic.
49-3000368 Rev 0